- 您現在的位置：買賣IC網 > PDF目錄367585 > LPC2290 (NXP Semiconductors N.V.) 16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface PDF資料下載
參數資料
| 型號： | LPC2290 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface |
| 中文描述： | 與CAN，16/32位ARM微控制器的10位模數轉換器和外部存儲器接口 |
| 文件頁數： | 19/41頁 |
| 文件大?。?/td> | 185K |
| 代理商： | LPC2290 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Philips Semiconductors
LPC2290
16/32-bit ARM microcontrollers with external memory interface
Preliminary data
Rev. 01 — 09 February 2004
19 of 41
9397 750 12874
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.9 External memory controller
The external Static Memory Controller is a module which provides an interface
between the system bus and external (off-chip) memory devices. It provides support
for up to four independently configurable memory banks (16 MBytes each with byte
lane enable control) simultaneously. Each memory banks is capable of supporting
SRAM, ROM, Flash EPROM, Burst ROM memory, or some external I/O devices.
Each memory bank may be 8, 16, or 32 bits wide.
6.10 General purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by
the GPIO registers. Pins may be dynamically configured as inputs or outputs.
Separate registers allow setting or clearing any number of outputs simultaneously.
The value of the output register may be read back, as well as the current state of the
port pins.
10:9
11
12
13
Reserved.
Controls the use of pin P3.26: 0 enables P3.26, 1 enables CS1.
Reserved.
If bits 25:23 are not 111, controls the use of pin P3.23/A23/XCLK: 0 enables P3.23,
1 enables XCLK.
Controls the use of pin P3.25: 00 enables P3.25, 01 enables CS2, 10 and 11 are
reserved values.
Controls the use of pin P3.24: 00 enables P3.24, 01 enables CS3, 10 and 11 are
reserved values.
Reserved.
If bits 5:4 are not 10, controls the use of pin P2.29:28: 0 enables P2.29:28, 1 is
reserved
If bits 5:4 are not 10, controls the use of pin P2.30: 0 enables P2.30, 1 enables
AIN4.
If bits 5:4 are not 10, controls the use of pin P2.31: 0 enables P2.31, 1 enables
AIN5.
Controls whether P3.0/A0 is a port pin (0) or an address line (1).
-
0
-
0
15:14
00
17:16
00
19:18
20
-
0
21
1
22
1
23
1 if BOOT1:0=00 at
RESET=0,
0 otherwise
BOOT1 during
Reset
000 if BOOT1:0=11
at Reset, 111
otherwise
24
Controls whether P3.1/A1 is a port pin (0) or an address line (1).
27:25
Controls the number of pins among P3.23/A23/XCLK and P3.22:2/A2.22:2 that are
address lines:
000 = None
100 = A11:2 are address lines.
001 = A3:2 are address lines.
101 = A15:2 are address lines.
010 = A5:2 are address lines.
110 = A19:2 are address lines.
011 = A7:2 are address lines.
111 = A23:2 are address lines.
Reserved.
31:28
Table 8:
PINSEL2 bits
Pin function select register 2 (PINSEL2 - 0xE002C014)
…continued
Description
Reset value
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2292 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| LPC2294JBD144 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| LPC2294 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| LPC2470 | Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface |
| LPD200P70 | PACKAGED HIGH DYNAMIC RANGE PHEMT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2290FBD144 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface |
| LPC2290FBD144,551 | 功能描述:ARM微控制器 - MCU RLESS/16K RM/2 CAN/ADC/EXT BUS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2290FBD144/01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontroller with CAN, 10-bit ADC and external memory interface |
| LPC2290FBD144/01,5 | 功能描述:ARM微控制器 - MCU ARM7 16KR/2CAN/ADC ROMLESS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2290FBD144551 | 制造商:NXP Semiconductors 功能描述:IC 16/32BIT MCU ARM7 SMD LPC2290 |
發布緊急采購，3分鐘左右您將得到回復。