- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2194HBD64 (NXP Semiconductors N.V.) Single-chip 16-32-bit microcontroller; 256 kB ISP-IAP flash with 10-bit ADC and CAN PDF資料下載
參數資料
| 型號： | LPC2194HBD64 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 數學處理器 |
| 英文描述： | Single-chip 16-32-bit microcontroller; 256 kB ISP-IAP flash with 10-bit ADC and CAN |
| 封裝： | LPC2194HBD64/01<SOT314-2 (LQFP64)|<<http://www.nxp.com/packages/SOT314-2.html<1<Always Pb-free,; |
| 文件頁數： | 22/41頁 |
| 文件大?。?/td> | 215K |
| 代理商： | LPC2194HBD64 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
LPC2194
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 6 — 14 June 2011
22 of 41
NXP Semiconductors
LPC2194
Single-chip 16/32-bit microcontroller
when an application does not require any peripherals to run at the full processor rate.
Because the APB divider is connected to the PLL output, the PLL remains active (if it was
running) during Idle mode.
6.19 Emulation and debugging
The LPC2194 support emulation and debugging via a JTAG serial port. A trace port allows
tracing program execution. Debugging and trace functions are multiplexed only with
GPIOs on Port 1. This means that all communication, timer and interface peripherals
residing on Port 0 are available during the development and debugging phase as they are
when the application is run in the embedded system itself.
6.19.1
EmbeddedICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of
the target system requires a host computer running the debugger software and an
EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts the Remote
Debug Protocol commands to the JTAG data needed to access the ARM core.
The ARM core has a Debug Communication Channel function built-in. The debug
communication channel allows a program running on the target to communicate with the
host debugger or another separate host without stopping the program flow or even
entering the debug state. The debug communication channel is accessed as a
co-processor 14 by the program running on the ARM7TDMI-S core. The debug
communication channel allows the JTAG port to be used for sending and receiving data
without affecting the normal program flow. The debug communication channel data and
control registers are mapped in to addresses in the EmbeddedICE logic.
The JTAG clock (TCK) must be slower than
1
6
of the CPU clock (CCLK) for the JTAG
interface to operate.
6.19.2
Embedded trace macrocell
Since the LPC2194 have significant amounts of on-chip memory, it is not possible to
determine how the processor core is operating simply by observing the external pins. The
Embedded Trace Macrocell (ETM) provides real-time trace capability for deeply
embedded processor cores. It outputs information about processor execution to the trace
port.
The ETM is connected directly to the ARM core and not to the main AMBA system bus. It
compresses the trace information and exports it through a narrow trace port. An external
trace port analyzer must capture the trace information under software debugger control.
Instruction trace (or PC trace) shows the flow of execution of the processor and provides a
list of all the instructions that were executed. Instruction trace is significantly compressed
by only broadcasting branch addresses as well as a set of status signals that indicate the
pipeline status on a cycle by cycle basis. Trace information generation can be controlled
by selecting the trigger resource. Trigger resources include address comparators,
counters and sequencers. Since trace information is compressed the software debugger
requires a static image of the code being executed. Self-modifying code can not be traced
because of this restriction.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2210FBD144 | 16-32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface |
| LPC2220FET144 | 16-32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface |
| LPC2212FBD144 | Single-chip 16-32-bit ARM microcontrollers; 128-256 kB ISP-IAP flash with 10-bit ADC and external memory interface |
| LPC2214FBD144 | Single-chip 16-32-bit ARM microcontrollers; 128-256 kB ISP-IAP flash with 10-bit ADC and external memory interface |
| LPC2290FBD144 | 16-32-bit ARM microcontroller with CAN, 10-bit ADC and external memory interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2194HBD64,151 | 功能描述:ARM微控制器 - MCU PREF PART LPC2194HBD64/01-S RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2194HBD64/00 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontroller; 256 kB ISP/IAP flash with 10-bit ADC and CAN |
| LPC2194HBD64/01 | 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64, Controller Family/Series:LPC2100, Core Size:16 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64, Controller Family/Series:LPC2100, Core Size:16bit / 32bit, No. of I/O's:46, Supply Voltage Min:1.65V, Supply Voltage Max:1.95V, Digital IC Case Style:LQFP, No. of Pins:64, Program Memory Size:256KB, |
| LPC2194HBD64/01,15 | 功能描述:ARM微控制器 - MCU ARM7 256KF/16KR/CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2194HBD64/0115 | 制造商:NXP Semiconductors 功能描述:MCU ARM7 64LQFP |
發布緊急采購，3分鐘左右您將得到回復。