參數資料
型號： LPC2136FBD64
廠商： NXP Semiconductors N.V.
元件分類： 數學處理器
英文描述： Single-chip 16-32-bit microcontrollers; 32-64-128-256-512 kB ISP-IAP flash with 10-bit ADC and DAC
封裝： LPC2131FBD64/01<SOT314-2 (LQFP64)|<<http://www.nxp.com/packages/SOT314-2.html<1<Always Pb-free,;LPC2131FBD64/01<SOT314-2 (LQFP64)|<<http://www.nxp.com/packages/SOT314-2.h
文件頁數： 22/45頁
文件大?。?/td> 381K
代理商： LPC2136FBD64
LPC2131_32_34_36_38
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5.1 — 29 July 2011
22 of 45
NXP Semiconductors
LPC2131/32/34/36/38
Single-chip 16/32-bit microcontrollers
Match register updates are synchronized with pulse outputs to prevent generation of
erroneous pulses. Software must ‘release’ new match values before they can become
effective.
May be used as a standard timer if the PWM mode is not enabled.
A 32-bit Timer/Counter with a programmable 32-bit Prescaler.
6.18 System control
6.18.1
Crystal oscillator
On-chip integrated oscillator operates with external crystal in range of 1 MHz to 30 MHz
and with external oscillator up to 50 MHz. The oscillator output frequency is called f
osc
and
the ARM processor clock frequency is referred to as CCLK for purposes of rate equations,
etc. f
osc
and CCLK are the same value unless the PLL is running and connected. Refer to
Section 6.18.2 “PLL”
for additional information.
6.18.2
PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up into the range of 10 MHz to 60 MHz with a Current Controlled
Oscillator (CCO). The multiplier can be an integer value from 1 to 32 (in practice, the
multiplier value cannot be higher than 6 on this family of microcontrollers due to the upper
frequency limit of the CPU). The CCO operates in the range of 156 MHz to 320 MHz, so
there is an additional divider in the loop to keep the CCO within its frequency range while
the PLL is providing the desired output frequency. The output divider may be set to divide
by 2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2,
it is insured that the PLL output has a 50 % duty cycle. The PLL is turned off and
bypassed following a chip reset and may be enabled by software. The program must
configure and activate the PLL, wait for the PLL to Lock, then connect to the PLL as a
clock source. The PLL settling time is 100
s.
6.18.3
Reset and wake-up timer
Reset has two sources on the LPC2131/32/34/36/38: the RESET pin and watchdog reset.
The RESET pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of
chip reset by any source starts the wake-up timer (see wake-up timer description below),
causing the internal chip reset to remain asserted until the external reset is de-asserted,
the oscillator is running, a fixed number of clocks have passed, and the on-chip flash
controller has completed its initialization.
When the internal reset is removed, the processor begins executing at address 0, which is
the reset vector. At that point, all of the processor and peripheral registers have been
initialized to predetermined values.
The wake-up timer ensures that the oscillator and other analog functions required for chip
operation are fully functional before the processor is allowed to execute instructions. This
is important at power on, all types of reset, and whenever any of the aforementioned
functions are turned off for any reason. Since the oscillator and other functions are turned
off during Power-down mode, any wake-up of the processor from Power-down mode
makes use of the wake-up timer.
相關PDF資料
PDF描述
LPC2138FBD64 Single-chip 16-32-bit microcontrollers; 32-64-128-256-512 kB ISP-IAP flash with 10-bit ADC and DAC
LPC2138FHN64 Single-chip 16-32-bit microcontrollers; 32-64-128-256-512 kB ISP-IAP flash with 10-bit ADC and DAC
LPC2141FBD64 Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
LPC2142FBD64 Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
LPC2144FBD64 Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
相關代理商/技術參數
參數描述
LPC2136FBD64,151 功能描述:ARM微控制器 - MCU 256K FL/32K RM/10B ADC/LV RTC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2136FBD64/01 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64, Controller Family/Series:LPC2100, Core Size:16 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-64, Controller Family/Series:LPC2100, Core Size:16bit / 32bit, No. of I/O's:47, Supply Voltage Min:3V, Supply Voltage Max:3.6V, Digital IC Case Style:LQFP, No. of Pins:64, Program Memory Size:256KB, RAM
LPC2136FBD64/01,15 功能描述:ARM微控制器 - MCU ARM7 256KF/32KR/ADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2136FBD64/01,15/REVF 制造商:NXP Semiconductors 功能描述:
LPC2136FBD64/01/S, 制造商:NXP Semiconductors 功能描述:- Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*