- 您現在的位置：買賣IC網 > PDF目錄11989 > LPC2103FHN48,551 (NXP Semiconductors)IC ARM7 MCU FLASH 32K 48-HVQFN PDF資料下載
參數資料
| 型號： | LPC2103FHN48,551 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 2/37頁 |
| 文件大小： | 0K |
| 描述： | IC ARM7 MCU FLASH 32K 48-HVQFN |
| 標準包裝： | 260 |
| 系列： | LPC2100 |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 70MHz |
| 連通性： | I²C，Microwire，SPI，SSI，SSP，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 8K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.65 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 48-VFQFN 裸露焊盤 |
| 包裝： | 托盤 |
| 配用： | 568-4310-ND - EVAL BOARD LPC2158 W/LCD 568-4302-ND - BOARD EVAL LPC210X KS2103 JLINK 568-4301-ND - BOARD EVAL LPC210X KS2103 568-4300-ND - BOARD EVAL LPC210X MCB2103 568-4297-ND - BOARD EVAL LPC21XX MCB2100 MCB2103UME-ND - BOARD EVAL MCB2103 + ULINK-ME MCB2103U-ND - BOARD EVAL MCB2103 + ULINK2 622-1005-ND - USB IN-CIRCUIT PROG ARM7 LPC2K |
| 其它名稱： | 568-4690 935287391551 LPC2103FHN48-S |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
LPC2101_02_03_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 2 June 2009
10 of 37
NXP Semiconductors
LPC2101/02/03
Single-chip 16-bit/32-bit microcontrollers
6.
Functional description
6.1 Architectural overview
The ARM7TDMI-S is a general purpose 32-bit microprocessor, which offers high
performance and very low power consumption. The ARM architecture is based on
Reduced Instruction Set Computer (RISC) principles, and the instruction set and related
decode mechanism are much simpler than those of microprogrammed Complex
Instruction Set Computers (CISC). This simplicity results in a high instruction throughput
and impressive real-time interrupt response from a small and cost-effective processor
core.
Pipeline techniques are employed so that all parts of the processing and memory systems
can operate continuously. Typically, while one instruction is being executed, its successor
is being decoded, and a third instruction is being fetched from memory.
The ARM7TDMI-S processor also employs a unique architectural strategy known as
Thumb, which makes it ideally suited to high-volume applications with memory
restrictions, or applications where code density is an issue.
The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the
ARM7TDMI-S processor has two instruction sets:
The standard 32-bit ARM set.
A 16-bit Thumb set.
The Thumb set’s 16-bit instruction length allows it to approach twice the density of
standard ARM code while retaining most of the ARM’s performance advantage over a
traditional 16-bit processor using 16-bit registers. This is possible because Thumb code
operates on the same 32-bit register set as ARM code.
Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the
performance of an equivalent ARM processor connected to a 16-bit memory system.
The particular ash implementation in the LPC2101/02/03 allows for full speed execution
also in ARM mode. It is recommended to program performance critical and short code
sections in ARM mode. The impact on the overall code size will be minimal but the speed
can be increased by 30 % over Thumb mode.
6.2 On-chip ash program memory
The LPC2101/02/03 incorporate a 8 kB, 16 kB or 32 kB ash memory system
respectively. This memory may be used for both code and data storage. Programming of
the ash memory may be accomplished in several ways. It may be programmed in system
via the serial port. The application program may also erase and/or program the ash while
the application is running, allowing a great degree of exibility for data storage eld
rmware upgrades, etc. The entire ash memory is available for user code as the
bootloader resides in a separate memory.
The LPC2101/02/03 ash memory provides a minimum of 100,000 erase/write cycles and
20 years of data-retention memory.
相關PDF資料 |
PDF描述 |
|---|---|
| 1394461-2 | CONN MALE CABLE COUPLER 14AWG |
| 1394461-1 | CONN MALE CABLE COUPLER 14AWG |
| VE-B4V-IY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
| COP8SAA716M7 | IC MCU OTP 8BIT 1K POR 16-SOIC |
| VE-B4V-IY-F2 | CONVERTER MOD DC/DC 5.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2103FHN48H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC |
| LPC2103FHN48H/6 | 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 70MHZ, HVQFN-48 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 70MHZ, HVQFN-48, Controller Family/Series:LPC2100, Core Size:1 |
| LPC2103FHN48H/6,51 | 功能描述:ARM微控制器 - MCU 16bit MCU 8KB FLASH 2KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2103FHN48H/6,518 | 制造商:NXP Semiconductors 功能描述:0 |
| LPC2103FHN48H/651 | 制造商:NXP Semiconductors 功能描述:MCU ARM7TDMI-S 32BIT 70MHZ |
發布緊急采購，3分鐘左右您將得到回復。