- 您現在的位置：買賣IC網 > PDF目錄384606 > LP5522TMX (NATIONAL SEMICONDUCTOR CORP) Programmable LED Driver PDF資料下載
參數資料
| 型號： | LP5522TMX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | Programmable LED Driver |
| 中文描述： | LED DISPLAY DRIVER, PBGA6 |
| 封裝： | 1.215 X 0.815 MM, 0.60 MM HEIGHT, 0.40 MM PITCH, MICRO SMD-6 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 219K |
| 代理商： | LP5522TMX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁
RUN ONCE COMMAND
Programmed blinking sequence is performed once after Run Once command. Four rising edges of CTRL signal within command
entering period is interpreted as Run Once command. If CTRL is kept high after command entering period the programmed blinking
sequence starts right after the blank period has elapsed. CTRL signal must stay high as long as programmed blinking sequence
is executed. If CTRL is set low during execution of blinking sequence, device goes to standby and execution of blinking sequence
is stopped.
20217219
If CTRL signal is low after command entering period, Run Once command is executed once the CTRL is set high.
20217250
TRAINING START COMMAND
Blinking sequence is programmed into memory in training mode. Blinking sequence is stored into volatile memory, thus removing
input voltage V
resets the memory. Memory can also be reset by giving Training Start and Training End commands without any
valid LED ON/OFF times.
LP5522 enters to Training mode after Training Start command. Two rising edges within command entering period is interpreted
as the Training Start command. The first LED ON time capturing is started once the rising edge of CTRL signal is detected after
the blank period. LED output follows CTRL signal during the programming.
The first LED ON time is recorded once CTRL signal is set low. Same time the first LED OFF time capturing is started. Programmed
blinking sequence can have one to three LED ON/OFF times. In order to be programmed correctly, at least one valid LED ON and
LED OFF time must be recorded.
20217251
9
www.national.com
L
相關PDF資料 |
PDF描述 |
|---|---|
| LP55271TL | Tiny LED Driver for Camera Flash and 4 LEDs with I2C Programmability, Connectivity Test and Audio Synchronization |
| LP55271TLX | Tiny LED Driver for Camera Flash and 4 LEDs with I2C Programmability, Connectivity Test and Audio Synchronization |
| LP55271 | Tiny LED Driver for Camera Flash and 4 LEDs with I2C Programmability, Connectivity Test and Audio Synchronization |
| LP5527 | Tiny LED Driver for Camera Flash and 4 LEDs with I2C Programmability, Connectivity Test and Audio Synchronization |
| LP5527TL | Tiny LED Driver for Camera Flash and 4 LEDs with I2C Programmability, Connectivity Test and Audio Synchronization |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP5522TMX/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LP5523 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable 9-Output LED Driver |
| LP55231 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LP55231 Programmable 9-Output LED Driver |
| LP55231SQE/NOPB | 功能描述:LED照明驅動器 Programmble 9-Output LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LP55231SQEVM | 制造商:Texas Instruments 功能描述:LP55231SQEVM - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:LED Lighting Development Tools LP55231SQ EVAL MOD |
發布緊急采購，3分鐘左右您將得到回復。