參數資料
型號: LNK306D
廠商: POWER INTEGRATIONS INC
元件分類: 穩壓器
英文描述: 1.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8
封裝: PLASTIC, SOP-8
文件頁數: 16/20頁
文件大?。?/td> 706K
代理商: LNK306D
2-5
LNK302/304-306
5
Rev. I 11/08
Figure 6a. Recommended Printed Circuit Layout for LinkSwitch-TN in a Buck Converter Conguration using P or G Package.
cycles are skipped. To provide overload protection if no cycles
are skipped during a 50 ms period, LinkSwitch-TN will enter
auto-restart (LNK304-306), limiting the average output power
to approximately 6% of the maximum overload power. Due to
tracking errors between the output voltage and the voltage across
C3 at light load or no load, a small pre-load may be required
(R4). For the design in Figure 5, if regulation to zero load is
required, then this value should be reduced to 2.4 k
Ω.
Key Application Considerations
LinkSwitch-TN Design Considerations
Output Current Table
Data sheet maximum output current table (Table 1) represents
the maximum practical continuous output current for both
mostlydiscontinuousconductionmode(MDCM)andcontinuous
conduction mode (CCM) of operation that can be delivered from
a given LinkSwitch-TN device under the following assumed
conditions:
1) Buck converter topology.
2) The minimum DC input voltage is ≥70 V. The value of
input capacitance should be large enough to meet this
criterion.
3) For CCM operation a KRP* of 0.4.
4) Output voltage of 12 VDC.
5) Efciency of 75%.
6) A catch/freewheeling diode with t
rr ≤75 ns is used for
MDCM operation and for CCM operation, a diode with
t
rr ≤35 ns is used.
7) The part is board mounted with SOURCE pins soldered
to a sufcient area of copper to keep the SOURCE pin
temperature at or below 100
°C.
*KRP is the ratio of ripple to peak inductor current.
LinkSwitch-TN Selection and Selection Between
MDCM and CCM Operation
Select the LinkSwitch-TN device, freewheeling diode and output
inductor that gives the lowest overall cost. In general, MDCM
+
PI-3750-121106
C2
L1
L2
R1
R3
RF1
D3
D4
D2
D1
C1
C3
C5
C4
Optimize hatched copper areas (
) for heatsinking and EMI.
D
S
FB
BP
S
LinkSwitch-TN
AC
INPUT
DC
OUTPUT
Figure 6b. Recommended Printed Circuit Layout for LinkSwitch-TN in a Buck Converter Conguration using D Package
to Bottom Side of the Board.
AC
INPUT
+
DC
OUTPUT
PI-4546-011807
Optimize hatched copper areas (
) for heatsinking and EMI.
S
BP
FB
D1
C2
R3
RF1
D3
D4
D2
R1
C1
C4
C5
C3
LinkSwitch-TN
L2
L1
D
相關PDF資料
PDF描述
LNK306DG-TL 1.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8
LNK302D 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8
LNK305P-TL 0.8 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDIP8
LNK306GTL 1.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8
LNK302GNTL 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
LNK306DG 功能描述:交流/直流開關轉換器 225 mA (MDCM) 360 mA (CCM) RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
LNK306DGTL 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:LinkSwitch-TN Family Lowest Component Count, Energy-Effi cient Off-Line Switcher IC
LNK306DG-TL 功能描述:交流/直流開關轉換器 225 mA (MDCM) 360 mA (CCM) RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
LNK306DN 功能描述:交流/直流開關轉換器 225 mA (MDCM) 360 mA (CCM) RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
LNK306DN0152-TL 制造商:Power Integrations 功能描述:1.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8