- 您現在的位置：買賣IC網 > PDF目錄44716 > LNK302GTL (POWER INTEGRATIONS INC) 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LNK302GTL |
| 廠商： | POWER INTEGRATIONS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | PLASTIC, SMD-8 |
| 文件頁數： | 15/16頁 |
| 文件大小： | 861K |
| 代理商： | LNK302GTL |
8
LNK302/304-306
G
3/05
be included for better EMI performance and higher line surge
withstand capability.
Quick Design Checklist
As with any power supply design, all LinkSwitch-TN designs
should be veried for proper functionality on the bench. The
following minimum tests are recommended:
1) Adequate DC rail voltage – check that the minimum DC
input voltage does not fall below 70VDC at maximum load,
minimum input voltage.
2) Correct Diode Selection – UF400x series diodes are
recommended only for designs that operate in MDCM at
an ambient of 70 °C or below. For designs operating in
continuousconductionmode(CCM)and/orhigherambients,
then a diode with a reverse recovery time of 35 ns or better,
such as the BYV26C, is recommended.
3) Maximum drain current – verify that the peak drain current
is below the data sheet peak drain specication under
worst-case conditions of highest line voltage, maximum
overload (just prior to auto-restart) and highest ambient
temperature.
4) Thermal check – at maximum output power, minimum
input voltage and maximum ambient temperature, verify
that the LinkSwitch-TN SOURCE pin temperature is
100 °C or below. This gure ensures adequate margin due
to variations in R
DS(ON) from part to part. A battery powered
thermocouplemeterisrecommendedtomakemeasurements
whentheSOURCEpinsareaswitchingnode.Alternatively,
the ambient temperature may be raised to indicate margin
to thermal shutdown.
In a LinkSwitch-TN design using a buck or buck boost converter
topology, the SOURCE pin is a switching node. Oscilloscope
measurements should therefore be made with probe grounded
to a DC voltage, such as primary return or DC input rail, and
not to the SOURCE pins. The power supply input must always
be supplied from an isolated source (e.g. via an isolation
transformer).
相關PDF資料 |
PDF描述 |
|---|---|
| LNK353G-TL | 0.4 A SWITCHING REGULATOR, 214 kHz SWITCHING FREQ-MAX, PDSO7 |
| LNK605GG | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LNK605GG-TL | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LNK616DG-TL | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LNK603DG | SPECIALTY ANALOG CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LNK302G-TL | 功能描述:IC OFFLINE SWIT OCP 8SMD RoHS:否 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:LinkSwitch®-TN 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR |
| LNK302P | 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:Lowest Component Count, Energy Efficient Off-Line Switcher IC |
| LNK302P/G/D | 制造商:FERYSTER 制造商全稱:FERYSTER Inductive Components Manufacturer 功能描述:Lowest Component Count, Energy-Effi cient Off-Line Switcher IC |
| LNK302PN | 功能描述:交流/直流開關轉換器 63mA MDCM 80mA CCM RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| LNK303P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3W電源方案LNK303P |
發布緊急采購，3分鐘左右您將得到回復。