- 您現在的位置：買賣IC網 > PDF目錄44715 > LNBP10SP (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO10 PDF資料下載
參數資料
| 型號： | LNBP10SP |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| 封裝： | POWER, SO-10 |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 204K |
| 代理商： | LNBP10SP |
accomplished thanks to the fast response of the
ENT input and the prompt oscillator start-up. This
helps designers who want to implement the
DiSEqC
protocols (*).
In order to improve design flexibility and to allow
implementation
of
newcoming
LNB
remote
control standards, an analogic modulation input
pin is available (EXTM). An appropriate DC
blocking capacitor must be used to couple the
modulating signal source to the EXTM pin. When
external modulation is not used, the relevant pin
can be left open.
Two pins are dedicated to the overcurrent
protection/monitoring: CEXT
and
OLF.
The
overcurrent protection circuit works dynamically:
as soon as an overload is detected in either LNB
output, the output is shut-down for a time Toff
determined by the capacitor connected between
CEXT and GND. Simultaneously the OLF pin,
that is an open collector diagnostic output flag,
from HIGH IMPEDANCE state goes LOW. After
the time has elapsed, the output is resumed for a
time ton=1/15toff (typ.) and OLF goes in HIGH
IMPEDANCE. If the overload is still present, the
protection circuit will cycle again through toff and
ton until the overload is removed. Typical ton+toff
value is 1200ms when a 4.7
F external capacitor
is used.
This dynamic operation can greatly reduce the
power dissipation in short circuit condition, still
ensuring excellent power-on start up even with
highly capacitive loads on LNB outputs.
The device is packaged in Multiwatt15 for
thru-holes mounting and in PowerSO-20 for
surface mounting. When a limited functionality in
a smaller package matches design needs, a
range of cost-effective PowerSO-10 solutions is
also offered. All versions have built-in thermal
protection against overheatingdamage.
(*): External components are needed to comply to level 2.x and above (bidirectional) DiSEqC
bus hardware requirements. DiSEqC is
a trademark of EUTELSAT.
ORDERING NUMBERS
Type
Multiwatt-15
PowerSO-20
PowerSO-10
LNBP10
LNBP11
LNBP12
LNBP13
LNBP14
LNBP15
LNBP16
LNBP20
LNBP20CR
LNBP20PD
LNBP10SP
LNBP11SP
LNBP12SP
LNBP13SP
LNBP14SP
LNBP15SP
LNBP16SP
PIN CONFIGURATIONS
Multiwatt-15
PowerSO-20
PowerSO-10
LNBP10 SERIES - LNBP20
2/18
相關PDF資料 |
PDF描述 |
|---|---|
| LNBP16SP | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP11SP | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP13SP | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP11LPUR | SWITCHING REGULATOR, PDSO8 |
| LNBP9LIT | SWITCHING REGULATOR, SFM5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LNBP10SP-TR | 功能描述:線性穩壓器 - 標準 LNBP voltage reg RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| LNBP11 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBP11LPUR | 功能描述:線性穩壓器 - 標準 LNB SUP/CTRL VLT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| LNBP11SP | 制造商:STMicroelectronics 功能描述:REG STD LIN SELECTABLE POS 13V/18V 0.8A 12PIN(10+2TAB) PWRSO - Rail/Tube |
| LNBP11SP-TR | 功能描述:線性穩壓器 - 標準 LNBP voltage reg RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。