- 您現在的位置：買賣IC網 > PDF目錄369808 > LNBK20D2 LNB SUPPLY AND CONTROL VOLTAGE REGULATOR (PARALLEL INTERFACE) PDF資料下載
參數資料
| 型號： | LNBK20D2 |
| 英文描述： | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR (PARALLEL INTERFACE) |
| 中文描述： | LNB電源與控制穩壓器（并行接口） |
| 文件頁數： | 11/14頁 |
| 文件大小： | 465K |
| 代理商： | LNBK20D2 |
LNBK20D2
11/14
THERMAL DESIGN NOTE
During normal operation, this device dissipates some power. At maximum rated output current (400mA),
the voltage drop on the linear regulator lead to a total dissipated power that is of about 2W. The heat
generated requires a suitable heatsink to keep the junction temperature below the over temperature
protection threshold. Assuming a 40°C temperature inside the Set-Top-Box case, the total Rthj-amb has
to be less than 43°C/W.
While this can be easily achieved using a through-hole power package that can be attached to a small
heatsink or to the metallic frame of the receiver, a surface mount power package must rely on PCB
solutions whose thermal efficiency is often limited. The simplest solution is to use a large, continuous
copper area of the GND layer to dissipate the heat coming from the IC body.
The SO-20 package of this IC has 4 GND pins that are not just intended for electrical GND connection, but
also to provide a low thermal resistance path between the silicon chip and the PCB heatsink. Given an
Rthj-c equal to 15°C/W, a maximum of 28°C/W are left to the PCB heatsink. This figure is achieved if a
minimum of 25cm
2
copper area is placed just below the IC body. This area can be the inner GND layer of
a multi-layer PCB, or, in a dual layer PCB, an unbroken GND area even on the opposite side where the
IC is placed. In both cases, the thermal path between the IC GND pins and the dissipating copper area
must exhibit a low thermal resistance.
In figure 4, it is shown a suggested layout for the SO-20 package with a dual layer PCB, where the IC
Ground pins and the square dissipating area are thermally connected through 32 vias holes, filled by
solder. This arrangement, when L=50mm, achieves an Rthc-a of about 28°C/W.
Different layouts are possible, too. Basic principles, however, suggest to keep the IC and its ground pins
approximately in the middle of the dissipating area; to provide as many vias as possible; to design a
dissipating area having a shape as square as possible and not interrupted by other copper traces.
SO-20 SUGGESTED PCB HEATSINK LAYOUT
相關PDF資料 |
PDF描述 |
|---|---|
| LNC710PS | Opto-Electronic Device - Light Emitting Diodes - Laser |
| LNCQ10PS | Opto-Electronic Device - Light Emitting Diodes - Laser |
| LNE150 | TRANSISTOR | MOSFET | N-CHANNEL | 500V V(BR)DSS | TO-236AB |
| LNE150K1 | TRANSISTOR | MOSFET | N-CHANNEL | 500V V(BR)DSS | TO-236AB |
| LNG129WHA | Opto-Electronic Device - Visible Light Emitting Diodes - Point-Lighting LEDs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LNBK20D2-TR | 功能描述:線性穩壓器 - 標準 LNB SUPPLY AND CONTROL Vltg REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| LNBK20PD | 功能描述:IC LNB SUPPLY & CNTRL 20-PWRSOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| LNBK20PD-TR | 功能描述:線性穩壓器 - 標準 VOLTAGE REGULATOR RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| LNBP10 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBP10LPUR | 功能描述:線性穩壓器 - 標準 LNB SUP/CTRL VLT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。