- 您現在的位置：買賣IC網 > PDF目錄44574 > LMZ14203EXTTZX-ADJ (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PSSO7 PDF資料下載
參數資料
| 型號： | LMZ14203EXTTZX-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PSSO7 |
| 封裝： | 10.16 X 13.77 MM, 4.57 MM HEIGHT, ROHS COMPLIANT, TO-PMOD-7 |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 3935K |
| 代理商： | LMZ14203EXTTZX-ADJ |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
Additionally note, the minimum off-time of 260 ns limits the
maximum duty ratio. Larger R
ON (lower FSW) should be se-
lected in any application requiring large duty ratio.
Discontinuous Conduction and Continuous Conduction
Modes
At light load the regulator will operate in discontinuous con-
duction mode (DCM). With load currents above the critical
conduction point, it will operate in continuous conduction
mode (CCM). When operating in DCM the switching cycle
begins at zero amps inductor current; increases up to a peak
value, and then recedes back to zero before the end of the
off-time. Note that during the period of time that inductor cur-
rent is zero, all load current is supplied by the output capacitor.
The next on-time period starts when the voltage on the at the
FB pin falls below the internal reference. The switching fre-
quency is lower in DCM and varies more with load current as
compared to CCM. Conversion efficiency in DCM is main-
tained since conduction and switching losses are reduced
with the smaller load and lower switching frequency. Operat-
ing frequency in DCM can be calculated as follows:
f
SW(DCM)VO*(VIN-1)*6.8μH*1.18*10
20
*I
O/(VIN–VO)*RON
2 (15)
In CCM, current flows through the inductor through the entire
switching cycle and never falls to zero during the off-time. The
switching frequency remains relatively constant with load cur-
rent and line voltage variations. The CCM operating frequen-
cy can be calculated using equation 7 above.
Following is a comparison pair of waveforms of the showing
both CCM (upper) and DCM operating modes.
CCM and DCM Operating Modes
V
IN = 24V, VO = 3.3V, IO = 3A/0.4A 2 μsec/div
30117812
The approximate formula for determining the DCM/CCM
boundary is as follows:
I
DCBVO*(VIN–VO)/(2*6.8 μH*fSW(CCM)*VIN) (16)
Following is a typical waveform showing the boundary condi-
tion.
Transition Mode Operation
V
IN = 24V, VO = 3.3V, IO = 0.5 A 2 μsec/div
30117814
The inductor internal to the module is 6.8
μH. This value was
chosen as a good balance between low and high input voltage
applications. The main parameter affected by the inductor is
the amplitude of the inductor ripple current (I
LR). ILR can be
calculated with:
I
LR P-P=VO*(VIN- VO)/(6.8H*fSW*VIN) (17)
Where V
IN is the maximum input voltage and fSW is deter-
mined from equation 10.
If the output current I
O is determined by assuming that IO =
I
L, the higher and lower peak of ILR can be determined. Be
aware that the lower peak of I
LR must be positive if CCM op-
eration is required.
POWER DISSIPATION AND BOARD THERMAL
REQUIREMENTS
For the design case of V
IN = 24V, VO = 3.3V, IO = 3A, TAMB
(MAX) = 85°C , and TJUNCTION = 125°C, the device must see a
thermal resistance from case to ambient of:
θ
CA< (TJ-MAX — TAMB(MAX)) / PIC-LOSS - θJC (18)
Given the typical thermal resistance from junction to case to
be 1.9 °C/W. Use the 85°C power dissipation curves in the
Typical Performance Characteristics section to estimate the
P
IC-LOSS for the application being designed. In this application
it is 2.25W.
θ
CA <(125 — 85) / 2.25W — 1.9 = 15.8
To reach
θ
CA = 15.8, the PCB is required to dissipate heat
effectively. With no airflow and no external heat, a good esti-
mate of the required board area covered by 1 oz. copper on
both the top and bottom metal layers is:
Board Area_cm2 > 500°C x cm2/W /
θ
CA (19)
As a result, approximately 31.5 square cm of 1 oz copper on
top and bottom layers is required for the PCB design. The
PCB copper heat sink must be connected to the exposed pad.
Approximately thirty six, 10mils (254
μm) thermal vias spaced
59mils (1.5 mm) apart must connect the top copper to the
bottom copper. For an example of a high thermal performance
PCB layout, refer to the Evaluation Board application note
AN-2024.
PC BOARD LAYOUT GUIDELINES
PC board layout is an important part of DC-DC converter de-
sign. Poor board layout can disrupt the performance of a DC-
DC converter and surrounding circuitry by contributing to EMI,
ground bounce and resistive voltage drop in the traces. These
can send erroneous signals to the DC-DC converter resulting
www.national.com
12
LMZ14203EXT
相關PDF資料 |
PDF描述 |
|---|---|
| LMZ14203EXTTZ-ADJ | SWITCHING REGULATOR, PSSO7 |
| LMZ3040-7ED4A | 3-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LMZ3040-7ED3AF | 3-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LMZ3040-7ED2 | 3-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LMZ3040-7D7F | 3-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMZ14203H | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Evaluation Board modules for high output voltage are easy-to-use DC-DC |
| LMZ14203H_1106 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:3A SIMPLE SWITCHER? Power Module for High Output Voltage |
| LMZ14203HEVAL/NOPB | 功能描述:電源管理IC開發工具 LMZ14203H EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LMZ14203HTZ | 制造商:Texas Instruments 功能描述:POWER MODULE, 42V, 3A, 7TOPMOD 制造商:Texas Instruments 功能描述:POWER MODULE, 42V, 3A, 7TOPMOD; Primary Input Voltage:42V; No. of Outputs:1; Output Voltage:30V; Output Current:3A; Voltage Regulator Case Style:TO-PMOD; No. of Pins:7; Operating Temperature Min:-40C; Operating Temperature ;RoHS Compliant: Yes |
| LMZ14203HTZ/NOPB | 功能描述:直流/直流開關轉換器 42V,3A PWR MODULE RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。