參數資料
型號： LMX2335USLBX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： XO, clock
英文描述： PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications
中文描述： PLL FREQUENCY SYNTHESIZER, 1200 MHz, PQCC16
封裝： PLASTIC, CSP-16
文件頁數： 29/48頁
文件大?。?/td> 3127K
代理商： LMX2335USLBX
Test Setups
(Continued)
LMX2335U and LMX2336U f
IN
Sensitivity Test Setup
10136740
The block diagram above illustrates the setup required to
measure the LMX2336U device’s RF1 input sensitivity level.
The
same
setup
is
used
LMX2336SLEEB Evaluation Boards. The RF2 input sensitiv-
ity test setup is similar to the RF1 sensitivity test setup. The
purpose of this test is to measure the acceptable signal level
to the f
RF1 input of the PLL chip. Outside the acceptable
signal range, the feedback divider begins to divide incor-
rectly and miscount the frequency.
The setup uses an open loop configuration. A power supply
is connected to V
cc
and the bias voltage is swept from 2.7V
to 5.5V. The RF2 PLL is powered down (PWDN RF2 Bit = 1).
By means of a signal generator, an RF signal is applied to
the f
IN
RF1 pin. The 3 dB pad provides a 50
match
between the PLL and the signal generator. The OSC
in
pin is
tied to V
. The N value is typically set to 10000 in Code
Loader, i.e. RF1 N_CNTRB Word = 156 and RF1 N_CNTRA
Word = 16 for PRE RF1 Bit = 0. The feedback divider output
is routed to the F
o
LD pin by selecting the
RF1 PLL N Divider
Output
word (F
LD Word = 6 or 14) in Code Loader. A
Universal Counter is connected to the F
o
LD pin and tied to
for
the
LMX2336TMEB/
the 10 MHz reference output of the signal generator. The
output of the feedback divider is thus monitored and should
be equal to f
IN
RF1 / N.
The f
RF1 input frequency and power level are then swept
with the signal generator. The measurements are repeated
at different temperatures, namely T
= -40C, +25C, and
+85C. Sensitivity is reached when the frequency error of the
divided RF input is greater than or equal to 1 Hz. The power
attenuation from the cable and the 3 dB pad must be ac-
counted for. The feedback divider will actually miscount if too
much or too little power is applied to the f
IN
RF1 input.
Therefore, the allowed input power level will be bounded by
the upper and lower sensitivity limits. In a typical application,
if the power level to the f
IN
RF1 input approaches the sen-
sitivity limits, this can introduce spurs and degradation in
phase noise. When the power level gets even closer to these
limits, or exceeds it, then the RF1 PLL loses lock.
The LMX2335U f
sensitivity test setup is very much similar
to the above test setup.
L
www.national.com
29
相關PDF資料
PDF描述
LMX2335UTM PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2335U PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2336 PLLatinum⑩ Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2336LSLB PLLatinum⑩ Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2336LTM PLLatinum⑩ Low Power Dual Frequency Synthesizer for RF Personal Communications
相關代理商/技術參數
參數描述
LMX2335UTM 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2335UTM/NOPB 功能描述:IC FREQ SYNTHESIZER DUAL 16TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:PLLatinum™ 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LMX2335UTMX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications
LMX2336 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum⑩ Dual Frequency Synthesizer for RF Personal Communications
LMX2336 WAF 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*