- 您現在的位置：買賣IC網 > PDF目錄358877 > LM96000CIMT (NATIONAL SEMICONDUCTOR CORP) Hardware Monitor with Integrated Fan Control PDF資料下載
參數資料
| 型號： | LM96000CIMT |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Hardware Monitor with Integrated Fan Control |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | MO-153AD, TSSOP-24 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 695K |
| 代理商： | LM96000CIMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Note 14:
Holding the SMBDAT and/or SMBCLK lines Low for a time interval greater than t
TIMEOUT
will reset the LM96000’s SMBus state machine, therefore setting
the SMBDAT pin to a high impedance state.
Functional Description
1.0 SMBUS
The LM96000 is compatible with devices that are compliant to the SMBus 2.0 specification. More information on this bus can be
found at: http://www.smbus.org/. Compatibility of SMBus2.0 to other buses is discussed in the SMBus 2.0 specification.
1.1 Addressing
LM96000 is designed to be used primarily in desktop systems that require only one monitoring device.
If only one LM96000 is used on the motherboard, the designer should be sure that the Address Enable/PWM3 pin is High during
the first SMBus communication addressing the LM96000. Address Enable/PWM3 is an open drain I/O pin that at power-on
defaults to the input state of Address Enable. A maximum of 10k pull-up resistance on Address Enable/PWM3 is required to
assure that the SMBus address of the device will be locked at 010 1110b, which is the default address of the LM96000.
During the first SMBus communication TACH4 and PWM3 can be used to change the SMBus address of the LM96000 to
0101101b or 0101100b. LM96000 address selection procedure:
A10 k
pull-down resistor to ground on the Address Enable/PWM3 pin is required. Upon power up, the LM96000 will be placed
into Address Enable mode and assign itself an SMBus address according to the state of the Address Select input. The
LM96000 will latch the address during the first valid SMBus transaction in which the first five bits of the targeted address match
those of the LM96000 address, 0 1011b. This feature eliminates the possibility of a glitch on the SMBus interfering with address
selection. When the PWM3/Address Enable pin is not used to change the SMBus address of the LM96000, it will remain in a
high state until the first communication with the LM96000.After the first SMBus transaction is completed PWM3 and TACH4 will
return to normal operation.
Address Enable
0
0
1
Address Select
0
1
X
Board Implementation
Pulled to ground through a 10 k
resistor
Pulled to 3.3V or to GND through a 10 k
resistor
Pulled to 3.3V through a 10 k
resistor
SMBus Address
010 1100b, 2Ch
010 1101b, 2Dh
010 1110b, 2Eh
In this way, up to three LM96000 devices can exists on an SMBus at any time. Multiple LM96000 devices can be used to monitor
additional processors and temperature zones. When using the non-default addresses additional circuitry will be required if TACH4
and PWM3 require to function correctly. Such circuitry could consist of GPIO pins from a micro-controller. During the first
communication the micro-controller would drive the Address Enable and Address Select pins to the proper state for the required
address. After the first SMBus communication the micro-controller would drive it’s pins into TRISTATE allowing TACH4 and
PWM3 to operate correctly.
20084604
2.0 FAN REGISTER DEVICE SET-UP
The BIOS will follow the following steps to configure the fan registers on the LM96000. The registers corresponding to each
function are listed. All steps may not be necessary if default values are acceptable. Regardless of all changes made by the BIOS
to the fan limit and parameter registers during configuration, the LM96000 will continue to operate based on default values until
the START bit (bit 0), in the Ready/Lock/Start/Override register (address 40h), is set. Once the fan mode is updated, by setting
the START bit to 1, the LM96000 will operate using the values that were set by the BIOS in the fan control limit and parameter
registers (adress 5Ch through 6Eh).
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM96000CIMTX | Hardware Monitor with Integrated Fan Control |
| LM9617CCEA | Monochrome CMOS Image Sensor VGA 30 FPS |
| LM9617 | Monochrome CMOS Image Sensor VGA 30 FPS |
| LM9628EVAL-KIT | LM9628 Color CMOS Image Sensor VGA 30 FPS |
| LM9628IEA | CABLE, 1TP, FOIL, DRN, 22AWG, 7/30, AWM2576, 2464 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM96000CIMT/NOPB | 功能描述:板上安裝溫度傳感器 HW Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM96000CIMT/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
| LM96000CIMTX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM96000CIMTX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM96000EVAL/NOPB | 功能描述:溫度傳感器開發工具 LM96000 EVAL RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
發布緊急采購，3分鐘左右您將得到回復。