- 您現在的位置：買賣IC網 > PDF目錄384601 > LM95213CISD (NATIONAL SEMICONDUCTOR CORP) 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs PDF資料下載
參數資料
| 型號： | LM95213CISD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| 封裝： | LLP-14 |
| 文件頁數： | 15/34頁 |
| 文件大小： | 415K |
| 代理商： | LM95213CISD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
30013830
FIGURE 6. TCRIT response diagram (masking options not included)
The TCRIT response diagram of
Figure 6
shows the local
temperature interaction with the Tcrit limit and hysteresis val-
ue. As can be seen in the diagram when the local temperature
exceeds the Tcrit limit register value the LTn Status bit is set
and the T_CRITn output(s) is/are activated. The Status bit(s)
and outputs are not deactivated until the temperature goes
below the value calculated by subtracting the Common Hys-
teresis value programmed from the limit. This diagram mainly
shows an example function of the hysteresis and is not meant
to show complete function of the possible settings and options
of all the TCRIT outputs and limit values.
1.10 DIODE FAULT DETECTION
The LM95213 is equipped with operational circuitry designed
to detect fault conditions concerning the remote diodes. In the
event that the D+ pin is detected as shorted to GND, D,
V
DD
or D+ is floating, the Remote Temperature reading
is –128.000 °C if signed format is selected and 0 °C if un-
signed format is selected. In addition, the appropriate status
register bits RD1M or RD2M (D1 or D0) are set.
1.11 COMMUNICATING WITH THE LM95213
The data registers in the LM95213 are selected by the Com-
mand Register. At power-up the Command Register is set to
“00”, the location for the Read Local Temperature Register.
The Command Register latches the last location it was set to.
Each data register in the LM95213 falls into one of three types
of user accessibility:
1.
Read only
2.
Write only
3.
Write/Read same address
A
Write
to the LM95213 will always include the address byte
and the command byte. A write to any register requires one
data byte.
Reading
the LM95213 can take place either of two ways:
1.
If the location latched in the Command Register is correct
(most of the time it is expected that the Command
Register will point to one of the Read Temperature
Registers because that will be the data most frequently
read from the LM95213), then the read can simply
consist of an address byte, followed by retrieving the data
byte.
2.
If the Command Register needs to be set, then an
address byte, command byte, repeat start, and another
address byte will accomplish a read.
The data byte has the most significant bit first. At the end of
a read, the LM95213 can accept either acknowledge or No
Acknowledge from the Master (No Acknowledge is typically
used as a signal for the slave that the Master has read its last
byte). It takes the LM95213 95 ms (typical, all channels en-
abled) to measure the temperature of the remote diodes and
internal diode. When retrieving all 11 bits from a previous re-
mote diode temperature measurement, the master must in-
sure that all 11 bits are from the same temperature
conversion. This may be achieved by reading the MSB reg-
ister first. The LSB will be locked after the MSB is read. The
LSB will be unlocked after being read. If the user reads MSBs
consecutively, each time the MSB is read, the LSB associated
with that temperature will be locked in and override the pre-
vious LSB value locked-in.
15
www.national.com
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM95213CISDX | 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs |
| LM95214 | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95214CISD | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95214CISDX | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95221CIMM | Dual Remote Diode Digital Temperature Sensor with SMBus Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM95213CISD/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95213CISDX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95213CISDX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95213EB/NOPB | 功能描述:溫度傳感器開發工具 LM95213EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| LM95214 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
發布緊急采購，3分鐘左右您將得到回復。