- 您現在的位置：買賣IC網 > PDF目錄384601 > LM94022QBIMGX (NATIONAL SEMICONDUCTOR CORP) 1.5V, SC70, Multi-Gain Analog Temperature Sensor with Class-AB Output PDF資料下載
參數資料
| 型號： | LM94022QBIMGX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 1.5V, SC70, Multi-Gain Analog Temperature Sensor with Class-AB Output |
| 中文描述： | ANALOG TEMP SENSOR-VOLTAGE, 0.898-2.298V, 2.70Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | SC-70, 5 PIN |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 804K |
| 代理商： | LM94022QBIMGX |
2.0 Mounting and Thermal
Conductivity
The LM94022 can be applied easily in the same way as other
integrated-circuit temperature sensors. It can be glued or ce-
mented to a surface.
To ensure good thermal conductivity, the backside of the
LM94022 die is directly attached to the GND pin (Pin 2). The
temperatures of the lands and traces to the other leads of the
LM94022 will also affect the temperature reading.
Alternatively, the LM94022 can be mounted inside a sealed-
end metal tube, and can then be dipped into a bath or screwed
into a threaded hole in a tank. As with any IC, the LM94022
and accompanying wiring and circuits must be kept insulated
and dry, to avoid leakage and corrosion. This is especially true
if the circuit may operate at cold temperatures where con-
densation can occur. If moisture creates a short circuit from
the output to ground or V
, the output from the LM94022 will
not be correct. Printed-circuit coatings are often used to en-
sure that moisture cannot corrode the leads or circuit traces.
The thermal resistance junction to ambient (
θ
) is the pa-
rameter used to calculate the rise of a device junction tem-
perature due to its power dissipation. The equation used to
calculate the rise in the LM94022's die temperature is
where T
A
is the ambient temperature, I
Q
is the quiescent cur-
rent, I
is the load current on the output, and V
is the output
voltage. For example, in an application where T
= 30 °C,
V
= 5 V, I
= 9 μ
A, Gain Select = 11, V
= 2.231 mV,
and I
= 2 μ
A, the junction temperature would be 30.021 °C,
showing a self-heating error of only 0.021°C. Since the
LM94022's junction temperature is the actual temperature
being measured, care should be taken to minimize the load
current that the LM94022 is required to drive.
Figure 1
shows
the thermal resistance of the LM94022.
NS Package
Number
Device Number
Thermal
Resistance (
θ
JA
)
415°C/W
LM94022BIMG
MAA05A
FIGURE 1. LM94022 Thermal Resistance
3.0 Output and Noise
Considerations
A push-pull output gives the LM94022 the ability to sink and
source significant current. This is beneficial when, for exam-
ple, driving dynamic loads like an input stage on an analog-
to-digital converter (ADC). In these applications the source
current is required to quickly charge the input capacitor of the
ADC. See the Applications Circuits section for more discus-
sion of this topic. The LM94022 is ideal for this and other
applications which require strong source or sink current.
The LM94022's supply-noise gain (the ratio of the AC signal
on V
to the AC signal on V
) was measured during bench
tests. It's typical attenuation is shown in the Typical Perfor-
mance Characteristics section. A load capacitor on the output
can help to filter noise.
For operation in very noisy environments, some bypass ca-
pacitance should be present on the supply within approxi-
mately 2 inches of the LM94022.
4.0 Capacitive Loads
The LM94022 handles capacitive loading well. In an extreme-
ly noisy environment, or when driving a switched sampling
input on an ADC, it may be necessary to add some filtering to
minimize noise coupling. Without any precautions, the
LM94022 can drive a capacitive load less than or equal to
1100 pF as shown in
Figure 2
. For capacitive loads greater
than 1100 pF, a series resistor may be required on the output,
as shown in
Figure 3
.
20143015
FIGURE 2. LM94022 No Decoupling Required for
Capacitive Loads Less than 1100 pF.
20143033
C
LOAD
Minimum R
S
3 k
Ω
1.5 k
Ω
800 Ω
1.1 nF to 99 nF
100 nF to 999 nF
1 μ
F
FIGURE 3. LM94022 with series resistor for capacitive
Loading greater than 1100 pF.
5.0 Output Voltage Shift
The LM94022 is very linear over temperature and supply volt-
age range. Due to the intrinsic behavior of an NMOS/PMOS
rail-to-rail buffer, a slight shift in the output can occur when
the supply voltage is ramped over the operating range of the
device. The location of the shift is determined by the relative
levels of V
and V
OUT
. The shift typically occurs when V
DD
-
V
OUT
= 1.0V.
This slight shift (a few millivolts) takes place over a wide
change (approximately 200 mV) in V
or V
. Since the
shift takes place over a wide temperature change of 5°C to
20°C, V
is always monotonic. The accuracy specifications
in the Electrical Characteristics table already include this pos-
sible shift.
6.0 Selectable Gain for Optimization
and In Situ Testing
The Gain Select digital inputs can be tied to the rails or can
be driven from digital outputs such as microcontroller GPIO
pins. In low-supply voltage applications, the ability to reduce
the gain to -5.5 mV/°C allows the LM94022 to operate over
the full -50 °C to 150 °C range. When a larger supply voltage
www.national.com
12
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM95213 | 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs |
| LM95213CISD | 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs |
| LM95213CISDX | 2-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface and TCRIT Outputs |
| LM95214 | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95214CISD | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM94022QBIMGX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM94023 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5V, micro SMD, Dual-Gain Analog Temperature Sensor with Class AB Output |
| LM94023BITME | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5V, micro SMD, Dual-Gain Analog Temperature Sensor with Class AB Output |
| LM94023BITME/NOPB | 功能描述:板上安裝溫度傳感器 1.5V,micro SMD,Dual- Gain Ana Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM94023BITME/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
發布緊急采購，3分鐘左右您將得到回復。