- 您現在的位置：買賣IC網 > PDF目錄385489 > LM8500 (National Semiconductor Corporation) Four Wire Resistive Touchscreen Controller with Brownout PDF資料下載
參數資料
| 型號： | LM8500 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Four Wire Resistive Touchscreen Controller with Brownout |
| 中文描述： | 四線電阻式觸摸屏控制器掉電 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 319K |
| 代理商： | LM8500 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁
8.0 Brownout Reset
(Continued)
If the Brownout Reset feature is enabled, the internal reset
will not be turned off until t
id
counts down to zero. The
internal reset will perform the same functions as external
reset. The device is guaranteed to operate at the specified
frequency down to the specified brownout voltage. After the
underflow, the logic is designed such that no additional
internal resets occur as long as V
CC
remains above the
brownout voltage.
The device is relatively immune to short duration negative
going V
transients (glitches). Proper filtering of the V
power supply voltage is essential for proper brownout func-
tionality. Power supply decoupling is vital even in battery
powered systems.
There are two optional brownout voltages. The part numbers
for the three versions of this device are:
LM8500, V
bor
= high voltage range.
LM8300, V
bor
= low voltage range.
LM8400, BOR is disabled.
Refer to the device specifications for the actual V
bor
volt-
ages.
High brownout voltage devices are guaranteed to operate at
10MHz down to the high brownout voltage. Low brownout
voltage devices are guaranteed to operate at 3.33MHz down
to the low brownout voltage. Low brownout voltage devices
are not guaranteed to operate at 10MHz down to the low
brownout voltage.
Under no circumstances should the RESET pin be allowed
to float. If the on chip Brownout Reset feature is being used,
the RESET pin should be connected directly to V
CC
. The
RESET input may also be connected to an external pull-up
resistor or to other external circuitry. The output of the brown-
out reset detector will always preset t
id
to a value between
120-128μs for the LM8500 and 360-384μs for the LM8300.
At this time, the internal reset will be generated.
If the BOR feature is disabled, then no internal resets are
generated. In this case, the external RESET must be used.
When BOR is disabled, this on-chip circuitry is disabled and
draws no DC current.
9.0 Calibration
The device supports two, five, and thirteen point calibration.
If desired, the calibration points can be stored internally in
the non-volatile storage element. During calibration time, the
device has the unique ability to check if the calibration points
make sense. For instance, if the desired calibration point
was to be at the upper left hand corner, but by accident, the
actual point detected was at the lower right hand corner, the
device will reject this point. This ensures the calibration
process is not performed incorrectly.
The calibration checking, can be enabled or disabled. If the
calibration checking is enabled, the controller will always
check the current calibration point being done against the
theoretical point and determine if the value is within
±
127 of
the raw A/D values. If this option is desired, the touch screen
driver must perform the calibration according to the calibra-
tion mapping for the two, five, and thirteen points as shown
in
Figure 5
,
Figure 6
, and
Figure 7
, respectively. The theo-
retical values for the two, five, and thirteen points are shown
in
Table 4
,
Table 5
, and
Table 6
respectively.
20037206
FIGURE 4. Brownout Reset Operation
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM8500HLQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500ILQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500IMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8500HLQ9 | 功能描述:IC TOUCHSCREEN CONTROLLER 44LLP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LM8500HMT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HVA9 | 功能描述:IC TOUCHSCREEN CONTROLLER 44PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LM8500ILQ9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500IMT9 | 功能描述:IC TOUCHSCREEN CONTROLLR 48TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。