- 您現在的位置：買賣IC網 > PDF目錄358873 > LM75BIM-3 (National Semiconductor Corporation) Digital Temperature Sensor and Thermal WATCHDOG? with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM75BIM-3 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Digital Temperature Sensor and Thermal WATCHDOG? with Two-Wire Interface |
| 中文描述： | 數字溫度傳感器和熱看門狗？與兩線接口 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 356K |
| 代理商： | LM75BIM-3 |
1.0 Functional Description
(Continued)
by crossing T
OS
, then reset, it can be activated again only by
Temperature going below T
HYST
. Again, it will remain active
indefinitely until being reset by a read. Placing the LM75 in
shutdown mode also resets the O.S. Output.
1.2 POWER UP AND POWER DOWN
The LM75 always powers up in a known state. The power up
default conditions are:
1.
Comparator mode
2.
T
OS
= 80C
3.
T
HYST
= 75C
4.
O.S. active low
5.
Pointer = “00”
If the LM75 is not connected to the I
2
C bus on power up, it
will act as a stand-alone thermostat with the above tempera-
ture settings.
When the supply voltage is less than about 1.7V, the LM75 is
considered powered down. As the supply voltage rises
above the nominal 1.7V power up threshold, the internal
registers are reset to the power up default values listed
above.
1.3 I
2
C BUS INTERFACE
The LM75 operates as a slave on the I
2
C bus, so the SCL
line is an input (no clock is generated by the LM75) and the
SDA line is a bi-directional serial data path. According to I
2
C
bus specifications, the LM75 has a 7-bit slave address. The
four most significant bits of the slave address are hard wired
inside the LM75 and are “1001”. The three least significant
bits of the address are assigned to pins A2–A0, and are set
by connecting these pins to ground for a low, (0); or to +V
S
for a high, (1).
Therefore, the complete slave address is:
1
0
0
1
A2
A1
A0
LSB
MSB
01265807
Note 14:
These interrupt mode resets of O.S. occur only when LM75 is read or placed in shutdown. Otherwise, O.S. would remain active indefinitely for any event.
FIGURE 4. O.S. Output Temperature Response Diagram
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM75DM-33R2 | 2-Wire Serial Temperature Sensor and Monitor |
| LM77000 | Power Operational Amplifiers |
| LM77000CP | Power Operational Amplifiers |
| LM77CIMM-5 | 9-Bit Sign Digital Temperature Sensor and Thermal Window Comparator with Two-Wire Interface |
| LM7800C | Series 3-Terminal Positive Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM75BIM-3/NOPB | 功能描述:板上安裝溫度傳感器 Digital Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BIM-3+ | 功能描述:板上安裝溫度傳感器 2-Wire Digital Temp Snsr & Thrml Wtchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BIM-3+T | 功能描述:板上安裝溫度傳感器 2-Wire Digital Temp Snsr & Thrml Wtchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BIM-5 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BIM-5/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。