- 您現在的位置：買賣IC網 > PDF目錄384601 > LM73CIMKX-1 (National Semiconductor Corporation) 2.7V, SOT-23, 11-to-14 Bit Digital Temperature Sensor with 2-Wire Interface PDF資料下載
參數資料
| 型號： | LM73CIMKX-1 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 2.7V, SOT-23, 11-to-14 Bit Digital Temperature Sensor with 2-Wire Interface |
| 中文描述： | 為2.7V，采用SOT - 23，11至14位數字溫度傳感器，2線接口 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 732K |
| 代理商： | LM73CIMKX-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁
2.0 LM73 Registers
(Continued)
2.5 T
LOW
LOWER-LIMIT REGISTER
Pointer Address 03h (R/W)
Reset State: 8000h (–256C)
D15
SIGN
D14
128C
D13
64C
D12
32C
D11
16C
D10
8C
D9
4C
D8
2C
D7
1C
D6
0.5C
D5
D4
D3
D2
D1
D0
0.25C
reserved
Bits
15:5
Name
Lower-Limit
Temperature
Description
If the measured temperature that is stored in the temperature register falls below this
user-programmable lower temperature limit, the ALERT pin will be deactivated and the T
LOW
flag in the Control/Status register will be set to 1. Two’s complement format.
Returns zeros upon read. Recommend writing zeros only in these bits.
4:0
Reserved
2.6 CONTROL/STATUS REGISTER
Pointer Address 04h (R/W)
Reset State: 08h
D7
D6
D5
D4
D3
D2
THI
D1
D0
DAV
TO_DIS
RES1
RES0
reserved
ALRT_STAT
TLOW
Bits
7
Name
Time-Out Disable
Description
Disable the time-out feature on the SMBDAT and SMBCLK lines if set to 1. Setting this bit
turns off the bus-idle timers, enabling the LM73 to operate at lowest shutdown current.
Selects one of four user-programmable temperature data resolutions
00: 0.25C/LSB, 11-bit word (10 bits plus sign)
01: 0.125C/LSB, 12-bit word (11 bits plus sign)
10: 0.0625C/LSB, 13-bit word (12 bits plus sign)
11: 0.03125C/LSB, 14-bit word (13 bits plus sign)
Always returns zero when read. Recommend customer write zero only.
Value is 0 when ALERT output is low. Value is 1 when ALERT output is high. The ALERT
output is reset under any of the following conditions: (1) Cleared by writing a 1 to the ALERT
Reset bit in the configuration register, (2) Measured temperature falls below the T
LOW
limit,
or (3) cleared via the ARA sequence. Recommend customer write zero only.
Bit is set to 1 when the measured temperature exceeds the T
HIGH
limit stored in the
programmable T
HIGH
register. Flag is reset to 0 when both of the following conditions are
met: (1) measured temperature no longer exceeds the programmed T
HIGH
limit
and
(2) upon
reading the Control/Status register. If the temperature is not longer above the T
HIGH
limit, this
status bit remains set until it is read by the master so that the system can check the history
of what caused the ALERT output to go active. This bit is not cleared after every read if the
measured temperature is still above the T
HIGH
limit.
Bit is set to 1 when the measured temperature falls below the T
LOW
limit stored in the
programmable T
LOW
register. Flag is reset to 0 when both of the following conditions are
met: (1) measured temperature is no longer below the programmed T
LOW
limit
and
(2) upon
reading the Control/Status register. If the temperature is no longer below the T
LOW
limit, the
status bit remains set until it is read by the master so that the system can check the history
of what cause the ALERT output to go active. This bit is not cleared after every read if
temperature is still below T
LOW
limit.
This bit is 0 when the LM73 is in the process of converting a new temperature. It is 1 when
the conversion is done. After initiating a temperature conversion while operating in the
one-shot mode, this status bit can be monitored to indicate when the conversion is done.
After triggering the one-shot conversion, the data in the temperature register is invalid until
this bit is high (that is, after completion of the conversion). On power-up, the LM73 is in
continuous conversion mode; while in continuous conversion mode (the default mode after
power-on reset) this bit will always be high. Recommend customer write zero only.
6:5
Temperature
Resolution
4
3
reserved
ALERT Pin Status
2
Temperature High
Flag
1
Temperature Low
Flag
0
Data Available Flag
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM73 | 2.7V, SOT-23, 11-to-14 Bit Digital Temperature Sensor with 2-Wire Interface |
| LM7301 | TUBULAR COMPRES.LUG/COLOR CODE (HDCL-350 |
| LM7301IM | Low Power, 4 MHz GBW, Rail-to-Rail Input-Output Operational Amplifier in TinyPak⑩ Package |
| LM7301IMX | Low Power, 4 MHz GBW, Rail-to-Rail Input-Output Operational Amplifier in TinyPak⑩ Package |
| LM7301IM5 | Low Power, 4 MHz GBW, Rail-to-Rail Input-Output Operational Amplifier in TinyPak⑩ Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM73CIMKX-1/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM73EVAL | 功能描述:BOARD EVALUATION FOR LM73 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:PowerWise® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LM73EVAL/NOPB | 功能描述:溫度傳感器開發工具 LM73 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| LM74 | 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| LM74_05 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:SPI/MICROWIRE⑩ 12-Bit Plus Sign Temperature Sensor |
發布緊急采購，3分鐘左右您將得到回復。