- 您現在的位置：買賣IC網 > PDF目錄369795 > LM62 PDF資料下載
參數資料
| 型號： | LM62 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 217K |
| 代理商： | LM62 |
Typical Performance Characteristics
printed circuit board as shown in Figure 2 (Continued)
To generate these curves the LM62 was mounted to a
1.0 Mounting
The LM62 can be applied easily in the same way as other
integrated-circuit temperature sensors. It can be glued or
cemented to a surface. The temperature that the LM62 is
sensing will be within about +0.2C of the surface tempera-
ture that LM62’s leads are attached to.
This presumes that the ambient air temperature is almost the
same as the surface temperature; if the air temperature were
much higher or lower than the surface temperature, the
actual temperature measured would be at an intermediate
temperature between the surface temperature and the air
temperature.
To ensure good thermal conductivity the backside of the
LM62 die is directly attached to the GND pin. The lands and
traces to the LM62 will, of course, be part of the printed
circuit board, which is the object whose temperature is being
measured. These printed circuit board lands and traces will
not cause the LM62’s temperature to deviate from the de-
sired temperature.
Alternatively, the LM62 can be mounted inside a sealed-end
metal tube, and can then be dipped into a bath or screwed
into a threaded hole in a tank. As with any IC, the LM62 and
accompanying wiring and circuits must be kept insulated and
dry, to avoid leakage and corrosion. This is especially true if
the circuit may operate at cold temperatures where conden-
sation can occur. Printed-circuit coatings and varnishes such
as Humiseal and epoxy paints or dips are often used to
ensure that moisture cannot corrode the LM62 or its connec-
tions.
The thermal resistance junction to ambient (
θ
) is the pa-
rameter used to calculate the rise of a device junction tem-
perature due to its power dissipation. For the LM62 the
equation used to calculate the rise in the die temperature is
as follows:
T
J
= T
A
+
θ
JA
[(+V
S
I
Q
) + (+V
S
V
O
) I
L
]
where I
Q
is the quiescent current and I
L
is the load current on
the output. Since the LM62’s junction temperature is the
actual temperature being measured care should be taken to
minimize the load current that the LM62 is required to drive.
Supply Voltage
vs Supply Current
DS100893-12
Start-Up Response
DS100893-22
DS100893-14
FIGURE 2. Printed Circuit Board Used
for Heat Sink to Generate All Curves.
1
2
" Square Printed Circuit Board
with 2 oz. Copper Foil or Similar.
L
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM6311 | |
| LM6321M | IC-SM-HIGH SPEED BUFFER |
| LM6321MX | Analog Buffer/Voltage Follower |
| LM6325 | |
| LM6402H | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM62_05 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:2.7V, 15.6 mV/∑C SOT-23 Temperature Sensor |
| LM620Z | 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED |
| LM621 | 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:RED OVAL LAMP LED |
| LM6211 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low Noise, RRO Operational Amplifier with CMOS Input and 24V Operation |
| LM6211MF | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。