- 您現在的位置：買賣IC網 > PDF目錄358870 > LM5115MM (National Semiconductor Corporation) Secondary Side Post Regulator Controller PDF資料下載
參數資料
| 型號： | LM5115MM |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Secondary Side Post Regulator Controller |
| 中文描述： | 次級端后穩壓控制器 |
| 文件頁數： | 9/17頁 |
| 文件大?。?/td> | 725K |
| 代理商： | LM5115MM |
Detailed Operating Description
The LM5115 controller contains all of the features necessary
to implement multiple output power converters utilizing the
Secondary Side Post Regulation (SSPR) technique. The
SSPR technique develops a highly efficient and well regu-
lated auxiliary output from the secondary side switching
waveform of an isolated power converter. Regulation of the
auxiliary output voltage is achieved by leading edge pulse
width modulation (PWM) of the main channel duty cycle.
Leading edge modulation is compatible with either current
mode or voltage mode control of the main output. The
LM5115 drives external high side and low side NMOS power
switches configured as a synchronous buck regulator. A
current sense amplifier provides overload protection and
operates over a wide common mode input range from 0V to
12V. Additional features include a low dropout (LDO) bias
regulator, error amplifier, precision reference, adaptive dead
time control of the gate driver signals and thermal shutdown.
A programmable oscillator provides a PWM clock signal
when the LM5115 is powered by a dc input (free-run mode)
instead of the phase signal of the main channel converter
(SSPR mode).
Low Drop-out Bias Regulator
(VCC)
The LM5115 contains an internal LDO regulator that oper-
ates over an input supply range from 4.5V to 30V. The output
of the regulator at the VCC pin is nominally regulated at 7V
and is internally current limited to 40mA. VCC is the main
supply to the internal logic, PWM controller, and gate driver
circuits. When power is applied to the VBIAS pin, the regu-
lator is enabled and sources current into an external capaci-
tor connected to the VCC pin. The recommended output
capacitor range for the VCC regulator is 0.1uF to 100uF.
When the voltage at the VCC pin reaches the VCC under-
voltage lockout threshold of 4.25V, the controller is enabled.
The controller is disabled if VCC falls below 4.0V (250mV
hysteresis). In applications where an appropriate regulated
dc bias supply is available, the LM5115 controller can be
powered directly through the VCC pin instead of the VBIAS
pin. In this configuration, it is recommended that the VCC
and the VBIAS pins be connected together such that the
external bias voltage is applied to both pins. The allowable
VCC range when biased from an external supply is 4.5V to
7V.
Synchronization (SYNC) and
Feed-forward (RAMP)
The pulsing “phase signal” from the main converter synchro-
nizes the PWM ramp and gate drive outputs of the LM5115.
The phase signal is the square wave output from the trans-
former secondary winding before rectification (
Figure 1
). A
resistor connected from the phase signal to the low imped-
ance SYNC pin produces a square wave current (I
) as
shown in
Figure 2
. A current comparator at the SYNC input
monitors I
relative to an internal 15μA reference. When
I
exceeds 15μA, the internal clock signal (CLK) is reset
and the capacitor connected to the RAMP begins to charge.
The current source that charges the RAMP capacitor is
equal to 3 times the I
current. The falling edge of the
phase signal sets the CLK signal and discharges the RAMP
capacitor until the next rising edge of the phase signal. The
RAMP capacitor is discharged to ground by a low imped-
ance (100
) n-channel MOSFET. The input impedance at
SYNC pin is 2.5k
which is normally much less than the
external SYNC pin resistance.
The RAMP and SYNC functions illustrated in
Figure 2
pro-
vide line voltage feed-forward to improve the regulation of
the auxiliary output when the input voltage of the main
converter changes. Varying the input voltage to the main
converter produces proportional variations in amplitude of
the phase signal. The main channel PWM controller adjusts
the pulse width of the phase signal to maintain constant
volt*seconds and a regulated main output as shown in
Fig-
ure 3
. The variation of the phase signal amplitude and dura-
tion are reflected in the slope and duty cycle of the RAMP
signal of the LM5115 (I
α
phase signal amplitude). As a
result, the duty cycle of the LM5115 is automatically adjusted
to regulate the auxiliary output voltage with virtually no
change in the PWM threshold voltage. Transient line regu-
20134912
FIGURE 2. Line Feed-forward Diagram
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM5115MMX | Secondary Side Post Regulator Controller |
| LM5152 | CABLE |
| LM5152BCN | Dual and Quad High Speed/Low Power 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers |
| LM520A | WARM WHITE LAMP LED |
| LM560A | WARM WHITE LAMP LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5115MMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Secondary Side Post Regulator Controller |
| LM5115MTC | 功能描述:開關變換器、穩壓器與控制器 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| LM5115MTC/MEY8 | 制造商:Texas Instruments 功能描述: |
| LM5115MTC/NOPB | 功能描述:DC/DC 開關控制器 Secondary Side Switching Reg RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM5115MTCX | 功能描述:開關變換器、穩壓器與控制器 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。