- 您現在的位置：買賣IC網 > PDF目錄98001 > LM5041BSDX (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 685 kHz SWITCHING FREQ-MAX, DSO16 PDF資料下載
參數資料
| 型號： | LM5041BSDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 685 kHz SWITCHING FREQ-MAX, DSO16 |
| 封裝： | 5 X 5 MM, LLP-16 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 426K |
| 代理商： | LM5041BSDX |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
30086404
PWM Comparator
The PWM comparator compares the slope compensated cur-
rent ramp signal to the loop error voltage from the internal
error amplifier (COMP pin). This comparator is optimized for
speed in order to achieve minimum controllable duty cycles.
The comparator polarity is such that 0V on the COMP pin will
produce zero duty cycle in the buck stage.
Error Amplifier
An internal high gain wide-bandwidth error amplifier is pro-
vided within the LM5041B. The amplifier’s non-inverting input
is tied to a 0.75V reference. The inverting input is connected
to the FB pin. In non-isolated applications the power converter
output is connected to the FB pin via the voltage setting re-
sistors. Loop compensation components are connected be-
tween the COMP and FB pins. For most isolated applications
the error amplifier function is implemented on the secondary
side of the converter and the internal error amp is not used.
The internal error amplifier is configured as an open drain
output and can be disabled by connecting the FB pin to
ground. An internal 5 k
pull-up resistor between the 5V ref-
erence and the COMP pin can be used as the pull-up for an
opto-coupler in isolated applications.
Current Limit/Current Sense
The LM5041B provides cycle-by-cycle over-current protec-
tion. If the voltage at the CS comparator (CS pin voltage plus
slope comp voltage) exceeds 0.5V the present buck stage
duty cycle is terminated (cycle by cycle current limit). A small
RC filter located near the controller is recommended to filter
current sense signals at the CS pin. An internal MOSFET dis-
charges the external CS pin for an additional 50 ns at the
beginning of each cycle to reduce the leading edge spike that
occurs when the buck stage MOSFET is turned on.
The LM5041B current sense and PWM comparators are very
fast, and may respond to short duration noise pulses. Layout
considerations are critical for the current sense filter and
sense resistor. The capacitor associated with the CS filter
must be placed close to the device and connected directly to
the pins of the controller (CS and GND). If a current sense
transformer is used, both leads of the transformer secondary
should be routed to the sense resistor, which should also be
located close to the IC. A resistor may be used for current
sensing instead of a transformer, located in the push-pull
transistor sources, but a low inductance type of resistor is re-
quired. When designing with a sense resistor, all of the noise
sensitive low power grounds should be connected together
around the IC and a single connection should be made to the
high current power ground (sense resistor ground point).
Oscillator and Sync Capability
The LM5041B oscillator is set by a single external resistor
connected between the RT pin and GND. To set a desired
oscillator frequency (F), the necessary RT resistor can be
calculated from:
The buck stage will switch at the oscillator frequency and each
push-pull output will switch at half the oscillator frequency in
a push-pull configuration. The LM5041B can also be syn-
chronized to an external clock. The external clock must have
a higher frequency than the free running frequency set by the
RT resistor. The clock signal should be capacitively coupled
into the RT pin with a 100 pF capacitor. A peak voltage level
greater than 3V is required for detection of the sync pulse.
The sync pulse width should be set in the 15 ns to 150 ns
range by the external components. The RT resistor is always
required, whether the oscillator is free running or externally
synchronized. The voltage at the RT pin is internally regulated
to 2V. The RT resistor should be located very close to the
device and connected directly to the pins of the IC (RT and
GND).
www.national.com
10
LM5041B
相關PDF資料 |
PDF描述 |
|---|---|
| LM555H-MLS/NOPB | PULSE; RECTANGULAR, TIMER, MBCY8 |
| LM565MDC | PHASE LOCKED LOOP, UUC |
| LM78CCVFX-J | SPECIALTY ANALOG CIRCUIT, PQFP44 |
| LM78S40CNMDA | 1.5 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, UUC |
| LM9617CCEA-2 | SPECIALTY ANALOG CIRCUIT, CQCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5041EVAL | 功能描述:BOARD EVALUATION LM5041 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM5041EVAL/NOPB | 功能描述:電源管理IC開發工具 LM5041 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5041MTC | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5041MTC | 制造商:Texas Instruments 功能描述:PWM CONTROLLER POWERWISE TSSOP16 |
| LM5041MTC/NOPB | 功能描述:電流型 PWM 控制器 Cascaded Pwm Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。