- 您現在的位置：買賣IC網 > PDF目錄358868 > LM5021MMX-1 (NATIONAL SEMICONDUCTOR CORP) AC-DC Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | LM5021MMX-1 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | AC-DC Current Mode PWM Controller |
| 中文描述： | 0.7 A SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 746K |
| 代理商： | LM5021MMX-1 |
Detailed Operating Description
(Continued)
SKIP CYCLE OPERATION
During light load conditions, the efficiency of the switching
power supply typically drops as the losses associated with
switching and operating bias currents of the converter be-
come a significant percentage of the power delivered to the
load. The largest component of the power loss is the switch-
ing loss associated with the gate driver and external MOS-
FET gate charge. Each PWM cycle consumes a finite amout
of energy as the MOSFET is turned on and then turned off.
These switching losses are proportional to the frequency of
operation. The Skip Cycle function integrated within the
LM5021 controller reduces the average switching frequency
to reduce switching losses and improve efficiency during
light load conditions.
When a light load condition occurs, the COMP pin voltage is
reduced by the voltage feedback loop to reduce the peak
current delivered by the controller. Referring to
Figure 6
, the
PWM comparator input tracks the COMP pin voltage through
a 1.25V level shift circuit and a 3:1 resistor divider. As the
COMP pin voltage falls, the input to the PWM comparator
falls proportionately. When the PWM comparator input falls
to 125mV, the Skip Cycle comparator detects the light load
condition and disables output pulses from the controller. The
controller continues to skip switching cycles until the power
supply output falls and the COMP pin voltage increases to
demand more output current. The number of cycles skipped
will depend on the load and the response time of the fre-
quency compensation network. Eventually the COMP volt-
age will increase when the voltage loop requires more cur-
rent to sustain the regulated output voltage. When the PWM
comparator input exceeds 130mV (5mV hysteresis), normal
fixed frequency switching resumes. Typical power supply
designs will produce a short burst of output pulses followed
by a long skip cycle interval. The average switching fre-
quency in the Skip Cycle mode can be a small fraction of the
normal operating frequency of the power supply.
20144221
FIGURE 5. Waveform at SS and COMP Pin due to Brief Overload
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM5021MMX-2 | AC-DC Current Mode PWM Controller |
| LM5021 | AC-DC Current Mode PWM Controller |
| LM5025A | Active Clamp Voltage Mode PWM Controller |
| LM5025AMTC | Active Clamp Voltage Mode PWM Controller |
| LM5025AMTCX | Active Clamp Voltage Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5021MMX-1/NOPB | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5021MMX-2 | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5021MMX-2/NOPB | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5021NA-1 | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5021NA-1/NOPB | 功能描述:電流型 PWM 控制器 AC-DC Current Mode PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。