- 您現在的位置：買賣IC網 > PDF目錄201870 > LM5010AHMHX (NATIONAL SEMICONDUCTOR CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LM5010AHMHX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | TSSOP-14 |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 399K |
| 代理商： | LM5010AHMHX |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
20153822
FIGURE 5. Inductor Current
To keep the circuit in continuous conduction mode, the max-
imum allowed ripple current is twice the minimum load cur-
rent, or 400 mAp-p. Using this value of ripple current, the
inductor (L1) is calculated using the following:
(11)
where F
S(min) is the minimum frequency of 154 kHz (205 kHz
- 25%) at V
IN(max).
This provides a minimum value for L1 - the next higher stan-
dard value (100 H) will be used. To prevent saturation, and
possible destructive current levels, L1 must be rated for the
peak current which occurs if the current limit and maximum
ripple current are reached simultaneously (I
PK in Figure 4).
The maximum ripple amplitude is calculated by re-arranging
Equation 11 using V
IN(max), FS(min), and the minimum inductor
value, based on the manufacturer’s tolerance. Assume, for
this exercise, the inductor’s tolerance is ±20%.
(12)
I
PK = ILIM + IOR(max) = 1.5A + 0.372A = 1.872A
where I
LIM is the maximum guaranteed current limit threshold.
At the nominal maximum load current of 1.0A, the peak in-
ductor current is 1.186A.
R
CL: Since it is obvious that the lower peak of the inductor
current waveform does not exceed 1.0A at maximum load
current (see Figure 5), it is not necessary to increase the cur-
rent limit threshold. Therefore R
CL is not needed for this
exercise. For applications where the lower peak exceeds
1.0A, see the section entitled Increasing The Current Limit
Threshold.
C1:
This capacitor limits the ripple voltage at VIN resulting
from the source impedance of the supply feeding this circuit,
and the on/off nature of the switch current into VIN. At maxi-
mum load current, when the buck switch turns on, the current
into VIN steps up from zero to the lower peak of the inductor
current waveform (I
PK- in Figure 5), ramps up to the peak val-
ue (I
PK+), then drops to zero at turn-off. The average current
into VIN during this on-time is the load current. For a worst
case calculation, C1 must supply this average current during
the maximum on-time. The maximum on-time is calculated at
V
IN = 6V using Equation 5, with a 25% tolerance added:
The voltage at VIN should not be allowed to drop below 5.5V
in order to maintain V
CC above its UVLO.
Normally a lower value can be used for C1 since the above
calculation is a worst case calculation which assumes the
power source has a high source impedance. A quality ceramic
capacitor with a low ESR should be used for C1.
C2 and R3:
Since the LM5010A requires a minimum of 25
mVp-p of ripple at the FB pin for proper operation, the required
ripple at V
OUT is increased by R1 and R2, and is equal to:
V
RIPPLE = 25 mVp-p x (R1 + R2)/R2 = 50 mVp-p
This necessary ripple voltage is created by the inductor ripple
current acting on C2’s ESR + R3. First, the minimum ripple
current, which occurs at minimum VIN, maximum inductor
value, and maximum frequency, is determined.
(13)
The minimum ESR for C2 is then equal to:
If the capacitor used for C2 does not have sufficient ESR, R3
is added in series as shown in the Block Diagram. The value
chosen for C2 is application dependent, and it is recommend-
ed that it be no smaller than 3.3 F. C2 affects the ripple at
V
OUT, and transient response. Experimentation is usually nec-
essary to determine the optimum value for C2.
www.national.com
12
LM5010A
相關PDF資料 |
PDF描述 |
|---|---|
| MC74LCX32D | LOW-VOLTAGE CMOS QUAD 2-INPUT OR GATE |
| MC74LCX32DT | LOW-VOLTAGE CMOS QUAD 2-INPUT OR GATE |
| MC74LCX32M | LOW-VOLTAGE CMOS QUAD 2-INPUT OR GATE |
| MC74LCX32SD | LOW-VOLTAGE CMOS QUAD 2-INPUT OR GATE |
| MC74LCX373DT | LOW-VOLTAGE CMOS OCTAL TRANSPARENT LATCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5010AMH | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5010AMH/NOPB | 功能描述:直流/直流開關轉換器 Hi Volt 1A Step Down Switching Reg RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5010AMHE | 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Down 6V to 75V 14-Pin TSSOP EP T/R |
| LM5010AMHE/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5010AMHX | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。