參數資料
型號: LM5007SD
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: High Voltage (80V) Step Down Switching Regulator
中文描述: 0.9 A SWITCHING REGULATOR, DSO8
封裝: 4 X 4 MM, LLP-8
文件頁數: 6/12頁
文件大?。?/td> 230K
代理商: LM5007SD
Hysteretic Control Circuit
Overview
(Continued)
The output voltage (Vout) can be programmed by two exter-
nal resistors as shown in
Figure 1
. The regulation point can
be calculated as follows:
V
OUT
= 2.5 x (R1 + R2) / R2
The feedback comparator in hysteretic regulators depend
upon the output ripple voltage to switch the output transistor
on and off at regular intervals. In order for the internal
comparator to respond quickly to changes in output voltage,
proportional to inductor current, a minimum amount of ca-
pacitor Equivalent Series Resistance (ESR) is required. A
ripple voltage of 25mV to 50mV is recommended at the
feedback pin (FB) for stable operation. In cases where the
intrinsic capacitor ESR is too small, additional series resis-
tance may be added.
For applications where lower output voltage ripple is re-
quired the load can be connected directly to the low ESR
output capacitor, as shown in
Figure 1
. The series resistor
(R) will degrade the load regulation. Another technique for
enhancing the ripple voltage at the FB pin is to place a
capacitor in parallel with the feedback divider resistor R1.
The addition of the capacitor reduces the attenuation of the
ripple voltage from the feedback divider
High Voltage Bias Regulator
The LM5007 contains an internal high voltage bias regulator.
The input pin (Vin) can be connected directly to line voltages
from 9 to 75 Volts. To avoid supply voltage transients due to
long lead inductances on the input pin (Vin Pin 8), it is always
recommended to connect low ESR ceramic chip capacitor
(
)
0.1μF) between "Vin" pin and "RTN" pin (pin 4), located
close to LM5007. The regulator is internally current limited to
10mA. Upon power up, the regulator is enabled and sources
current into an external capacitor connected to the Vcc pin.
When the voltage on the Vcc pin reaches the regulation point
of 7V, the controller output is enabled.
An external auxiliary supply voltage can be applied to the
Vcc pin. If the auxiliary voltage is greater than 7 Volts the
internal regulator will essentially shutoff, thus reducing inter-
nal power dissipation.
20078305
FIGURE 1. Low Ripple Output Configuration
L
www.national.com
6
相關PDF資料
PDF描述
LM5007SDX High Voltage (80V) Step Down Switching Regulator
LM5008 High Voltage (100V) Step Down Switching Regulator
LM5008MM High Voltage (100V) Step Down Switching Regulator
LM5008SD High Voltage (100V) Step Down Switching Regulator
LM6118 Fast Settling Dual Operational Amplifiers
相關代理商/技術參數
參數描述
LM5007SD/NOPB 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
LM5007SD/NOPB 制造商:Texas Instruments 功能描述:IC, DC/DC CONVERTER
LM5007SD-EVAL 功能描述:電源管理IC開發工具 LM5007SD EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM5007SD-EVAL 制造商:Texas Instruments 功能描述:EVAL BOARD, LM5007 10V, 400mA SYNC STEP-
LM5007SD-EVAL/NOPB 功能描述:EVALUATION BOARD FOR LM5007SD RoHS:是 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC,步升 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969