- 您現在的位置：買賣IC網 > PDF目錄358868 > LM5000SDX-6EP (NATIONAL SEMICONDUCTOR CORP) High Voltage Switch Mode Regulator PDF資料下載
參數資料
| 型號： | LM5000SDX-6EP |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | High Voltage Switch Mode Regulator |
| 中文描述： | 2.7 A SWITCHING REGULATOR, 1545 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | PLASTIC, LLP-16 |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 438K |
| 代理商： | LM5000SDX-6EP |
Operation
CONTINUOUS CONDUCTION MODE
The LM5000EP is a current-mode, PWM regulator. When
used as a boost regulator the input voltage is stepped up to
a higher output voltage. In continuous conduction mode
(when the inductor current never reaches zero at steady
state), the boost regulator operates in two cycles.
In the first cycle of operation, shown in
Figure 3
(a), the
transistor is closed and the diode is reverse biased. Energy
is collected in the inductor and the load current is supplied by
C
OUT
.
The second cycle is shown in
Figure 3
(b). During this cycle,
the transistor is open and the diode is forward biased. The
energy stored in the inductor is transferred to the load and
output capacitor.
The ratio of these two cycles determines the output voltage.
The output voltage is defined approximately as:
where D is the duty cycle of the switch, D and D' will be
required for design calculations.
SETTING THE OUTPUT VOLTAGE
The output voltage is set using the feedback pin and a
resistor divider connected to the output as shown in
Figure 1
.
The feedback pin is always at 1.259V, so the ratio of the
feedback resistors sets the output voltage.
INTRODUCTION TO COMPENSATION
20098302
FIGURE 3. Simplified Boost Converter Diagram
(a) First Cycle of Operation (b) Second Cycle Of Operation
20098305
FIGURE 4. (a) Inductor current. (b) Diode current.
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM5000SDX-6 | High Voltage Switch Mode Regulator |
| LM5000-3MTCX | High Voltage Switch Mode Regulator |
| LM5000-3MTC | High Voltage Switch Mode Regulator |
| LM5000 | High Voltage Switch Mode Regulator |
| LM5010MH | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5001 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Voltage Switch Mode Regulator |
| LM5001_09 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Voltage Switch Mode Regulator |
| LM5001BSTEVAL/NOPB | 功能描述:電源管理IC開發工具 LM5001BST EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5001IDRQ1 | 功能描述:Boost, Flyback, Forward Converter, SEPIC Switching Regulator IC Positive, Isolation Capable Adjustable 3.1V 1 Output 800mA (Switch) 8-SOIC (0.154", 3.90mm Width) 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 功能:升壓，升壓/降壓 輸出配置:正，可提供隔離 拓?fù)?升壓，反激式，正向轉換器，SEPIC 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.1V 電壓 - 輸入（最大值）:75V 電壓 - 輸出（最小值/固定）:3.1V 電壓 - 輸出（最大值）:76V（開關） 電流 - 輸出:800mA（開關） 頻率 - 開關:50kHz ~ 1.5MHz 同步整流器:無 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:1 |
| LM5001ISOEVAL | 功能描述:BOARD EVALUATION LM5001ISO RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。