- 您現在的位置：買賣IC網 > PDF目錄385488 > LM4992 (National Semiconductor Corporation) 420mW Stereo Cell Phone Audio Amplifier PDF資料下載
參數資料
| 型號： | LM4992 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | 420mW Stereo Cell Phone Audio Amplifier |
| 中文描述： | 420mW立體聲手機音頻放大器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 576K |
| 代理商： | LM4992 |
Application Information
(Continued)
nates possible high frequency oscillations. Care should be
taken when calculating the -3dB frequency in that an incor-
rect combination of R
3
and C
4
will cause rolloff before
20kHz. A typical combination of feedback resistor and ca-
pacitor that will not produce audio band high frequency rolloff
is R
= 20k
and C
= 25pf. These components result in a
-3dB point of approximately 320 kHz.
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
"rule-of-thumb" recommendations and the actual results will
depend heavily on the final layout.
GENERAL MIXED SIGNAL LAYOUT
RECOMMENDATION
Power and Ground Circuits
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
require a greater amount of design time but will not increase
the final price of the board. The only extra parts required will
be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A "Pi-filter" can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signal traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM5041 | Cascaded PWM Controller |
| LM5041MTC | Cascaded PWM Controller |
| LM5041MTCX | Cascaded PWM Controller |
| LM5041SD | Cascaded PWM Controller |
| LM5041SDX | Cascaded PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4992SD | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4992SD/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4992SDBD | 功能描述:音頻 IC 開發工具 LM4992SD EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4992SDBD/NOPB | 制造商:Texas Instruments 功能描述:Evaluation Board For LM4992, 420Mw Stereo Cell Phone Audio Amplifier |
| LM4992SDX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。