- 您現在的位置：買賣IC網 > PDF目錄30752 > LM4836MTE/NOPB (NATIONAL SEMICONDUCTOR CORP) 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | LM4836MTE/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 22/28頁 |
| 文件大小： | 951K |
| 代理商： | LM4836MTE/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Electrical Characteristics for Single-Ended Mode Operation (Continued)
(Notes 8, 12) The following specifications apply for V
DD = 5V and TA = 25C unless otherwise noted.
Symbol
Parameter
Conditions
LM4836
Units
(Limits)
Typical
Limit
SNR
Signal to Noise Ratio
P
OUT =75 mW, R L =32
, A-Wtd
Filter
102
dB
X
talk
Channel Separation
f=1kHz, C
B = 1.0 F
65
dB
Electrical Characteristics for Bridged Mode Operation
(Notes 8, 12) The following specifications apply for V
DD = 5V and TA = 25C unless otherwise noted.
Symbol
Parameter
Conditions
LM4836
Units
(Limits)
Typical
Limit
V
OS
Output Offset Voltage
V
IN = 0V
10
50
mV (max)
P
O
Output Power
THD+N= 1.0%; f=1kHz; R
L =3
(Notes 9, 11)
2.2
W
THD+N= 1.0%; f=1kHz; R
L =4
(Notes 10, 11)
2W
THD = 1.5% (max);f = 1 kHz;
R
L =8
1.1
1.0
W (min)
THD+N = 10%;f = 1 kHz; R
L =8
1.5
W
THD+N
Total Harmonic Distortion+Noise
P
O = 1W, 20 Hz< f < 20 kHz,
R
L =8
,A
VD =2
0.3
%
P
O = 340 mW, RL =32
1.0
%
PSRR
Power Supply Rejection Ratio
C
B = 1.0 F, f = 120 Hz,
V
RIPPLE = 200 mVrms; RL =8
74
dB
SNR
Signal to Noise Ratio
V
DD = 5V, POUT = 1.1W, RL =8
,
A-Wtd Filter
93
dB
X
talk
Channel Separation
f=1kHz, C
B = 1.0 F
70
dB
Note 3: The
θJA given is for an MXA28A package whose exposed-DAP is soldered to an exposed 2in 2 piece of 1 ounce printed circuit board copper.
Note 4: The
θJA given is for an MXA28A package whose exposed-DAP is soldered to a 2in2 piece of 1 ounce printed circuit board copper on a bottom side layer
through 21 8mil vias.
Note 5: The
θJA given is for an MXA28A package whose exposed-DAP is soldered to an exposed 1in 2 piece of 1 ounce printed circuit board copper.
Note 6: The
θJA given is for an MXA28A package whose exposed-DAP is not soldered to any copper.
Note 7: The given
θJA is for an LM4836 packaged in an LQA24A with the exposed-DAP soldered to an exposed 2in2 area of 1oz printed circuit board copper.
Note 8: All voltages are measured with respect to the ground pins, unless otherwise specified. All specifications are tested using the typical application as shown
in Figure 2.
Note 9: When driving 3
loads and operating on a 5V supply the LM4836MTE exposed DAP must be soldered to the circuit board and forced-air cooled.
Note 10: When driving 4
loads and operating on a 5V supply the LM4836MTE exposed DAP must be soldered to the circuit board.
Note 11: When driving 3
or 4 loads and operating on a 5V supply, the LM4836LQ must be mounted to the circuit board that has a minimum of 2.5in2 of exposed,
uninterrupted copper area connected to the LLP package’s exposed DAP.
Note 12: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 13: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θ JA, and the ambient temperature TA. The maximum
allowable power dissipation is PDMAX =(TJMAX TA )/θJA. For the LM4836, TJMAX = 150C. The typical junction-to-ambient thermal resistance, when board mounted,
is 80C/W for the MTC28 package, 41C/W for the MXA28A package, and 42C/W for the LQA028AA package.
Note 14: Human body model, 100 pF discharged through a 1.5 k
resistor.
Note 15: Machine Model, 220 pF–240 pF discharged through all pins.
Note 16: Typicals are measured at 25C and represent the parametric norm.
Note 17: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
LM4836
www.national.com
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM4836MT/NOPB | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| LM4838MTE/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4838MT/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4838ITL/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PBGA36 |
| LM4838ITLX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PBGA36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4836MTEX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4836MTEX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4836MTX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Audio Amplifier |
| LM4836MTX/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4837MT | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。