- 您現在的位置：買賣IC網 > PDF目錄16817 > LM4819MBD (National Semiconductor)BOARD EVALUATION LM4819M PDF資料下載
參數資料
| 型號： | LM4819MBD |
| 廠商： | National Semiconductor |
| 文件頁數： | 4/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION LM4819M |
| 標準包裝： | 1 |
| 系列： | Boomer® |
| 放大器類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 350mW x 1 @ 16 歐姆 |
| 電源電壓： | 2 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 板類型： | 完全填充 |
| 已用 IC / 零件： | LM4819 |
| 已供物品： | 板 |
| 相關產品： | LM4819M/NOPB-ND - IC AMP AUDIO PWR .35W MONO 8SOIC LM4819MX/NOPBTR-ND - IC AMP AUDIO PWR .35W MONO 8SOIC LM4819MM-ND - IC AMP AUDIO PWR .35W MONO 8MSOP LM4819MMX-ND - IC AMP AUDIO PWR .35W MONO 8MSOP |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
SNAS133D – FEBRUARY 2001 – REVISED MARCH 2013
Besides affecting system cost and size, Ci has an effect on the LM4819's click and pop performance. When the
supply voltage is first applied, a transient (pop) is created as the charge on the input capacitor changes from zero
to a quiescent state. The magnitude of the pop is directly proportional to the input capacitor's value. Higher value
capacitors need more time to reach a quiescent DC voltage (usually 1/2 VDD) when charged with a fixed current.
The amplifier's output charges the input capacitor through the feedback resistor, RF. Thus, selecting an input
capacitor value that is no higher than necessary to meet the desired -3dB frequency can minimize pops.
As shown in Figure 1, the input resistor (Ri) and the input capacitor, Ci produce a -3dB high pass filter cutoff
frequency that is found using Equation 5.
f-3dB = 1/(2 πRiCi) (Hz)
(5)
As an example when using a speaker with a low frequency limit of 150Hz, Ci, using Equation 5 is 0.063F. The
0.39F Ci shown in Figure 1 allows the LM4819 to drive a high efficiency, full range speaker whose response
extends down to 20Hz.
Besides optimizing the input capacitor value, the bypass capacitor value, CB requires careful consideration. The
bypass capacitor's value is the most critical to minimizing turn-on pops because it determines how fast the
LM4819 turns on. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the
smaller the turn-on pop. While the device will function properly (no oscillations or motorboating), with CB less
than 1.0F, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to or
greater than 1.0F is recommended in all but the most cost sensitive designs.
Bypass Capacitor Value Selection
Besides minimizing the input capacitor size, careful consideration should be paid to the value of CB, the capacitor
connected to the BYPASS pin. Since CB determines how fast the LM4819 settles to quiescent operation, its
value is critical when minimizing turn-on pops. The slower the LM4819's outputs ramp to their quiescent DC
voltage (nominally 1/2VDD), the smaller the turn-on pop. Choosing CB equal to 1.0F along with a small value of
Ci (in the range of 0.1F to 0.39F) produces a click-less and pop-less shutdown function. As discussed above,
choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops.
Optimizing Click and Pop Reduction Performance
The LM4819 contains circuitry that minimizes turn-on and shutdown transients or "clicks and pops". For this
discussion, turn on refers to either applying the power or supply voltage or when the shutdown mode is
deactivated. While the power supply is ramping to it's final value, the LM4819's internal amplifiers are configured
as unity gain buffers. An internal current source charges the voltage of the bypass capacitor, CB, connected to
the BYPASS pin in a controlled, linear manner. Ideally, the input and outputs track the voltage charging on the
bypass capacitor. The gain of the internal amplifiers remains unity until the bypass capacitor is fully charged to
1/2VDD. As soon as the voltage on the bypass capacitor is stable, the device becomes fully operational. Although
the BYPASS pin current cannot be modified, changing the size of the bypass capacitor, CB, alters the device's
turn-on time and magnitude of "clicks and pops". Increasing the value of CB reduces the magnitude of turn-on
pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time (Ton) increases. There is a
linear relationship between the size of CB and the turn on time. Below are some typical turn-on times for various
values of CB:
CB
TON
0.01F
20ms
0.1F
200ms
0.22F
440ms
0.47F
940ms
1.0F
2S
12
Copyright 2001–2013, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| 50YXG47MEFC6.3X11 | CAP ALUM 47UF 50V 20% RADIAL |
| NCP2890EVB | EVAL BOARD FOR NCP2890 |
| V150B36E150BF3 | CONVERTER MOD DC/DC 36V 150W |
| 1812R-823J | INDUCTOR UNSHIELDED 82UH SMD |
| RBA10DRMT-S288 | CONN EDGECARD 20POS .125 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4819MBD/NOPB | 功能描述:音頻 IC 開發(fā)工具 LM4819MBD EVAL MOD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4819MM | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4819MM/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4819MMX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4819MMX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。