- 您現在的位置：買賣IC網 > PDF目錄30751 > LM4753T (NATIONAL SEMICONDUCTOR CORP) 11.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 PDF資料下載
參數資料
| 型號： | LM4753T |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 11.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| 封裝： | TO-220, 15 PIN |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 511K |
| 代理商： | LM4753T |
Application Information (Continued)
In
Figure 7, a 50 kHz input signal is used to show the clipping
and attenuating effect of the LM4753 when coming out of
thermal shutdown.
THERMAL CONSIDERATIONS
Determining Maximum Power Dissipation
It is important to determine the maximum amount of package
power dissipation in order to choose an adequate heat sink.
Improper heat sinking can lead to premature thermal shut-
down operation, causing music to cut out.
Equation (2) can
be used to calculate the approximate maximum integrated
circuit power dissipation for your amplifier design, given the
supply voltage, and rated load, with both channels being
driven simultaneously.
P
DMAX = 2(VCCtot
2/2
π2R
L)
(2)
To ensure that a proper heat sink is chosen, be sure to take
into account the effects of the unregulated power supply volt-
age variation and the highly reactive load impedance varia-
tion over frequency.
A poorly regulated power supply can have a supply voltage
variation of more than 10V. Be sure to take into account the
no-load power supply voltage.
A nominally rated 8
load can have an impedance dip down
to 5
at low frequencies. As well, the load is not purely resis-
tive, and this causes the amplifier output current to be out of
phase with the output voltage. When the current and voltage
are out of phase, the internal power dissipation actually in-
creases.
Equation (2) can be directly applied to the Power Dissipation
vs Output Power curves in the Typical Performance Charac-
teristics section. However, the curves take into account qui-
escent power dissipation which
Equation (2) does not. The
curves are to be used as a guideline in determining the re-
quired heat sink and are not intended to provide exact power
dissipation values.
Heat Sinking
Choosing a heat sink for a high-power audio amplifier is
made entirely to keep the die temperature below its maxi-
mum junction temperature, so that the thermal protection cir-
cuitry does not operate under normal circumstances. The
heat sink should be chosen to dissipate the maximum IC
power for the maximum no-load supply voltage and the mini-
mum load impedance.
Referring to
Figure 8, the thermal resistance from the die
(junction) to the outside air (ambient) is a combination of
three thermal resistances,
θ
JC, θCS and θSA. Two of these
thermal resistances are provided by National,
θ
JC and θCS.
Since convection heat flow (power dissipation) is analogous
to current flow, thermal resistance is analogous to electrical
resistance, and temperature drops are analogous to voltage
drops, the power dissipation out of the LM4753 is equal to
the following:
P
DMAX = (TJMAX –TAMB)/θJA
(3)
The thermal resistance,
θ
JA is equal to θJC + θCS + θSA,
where
θ
JC is the junction-to-case thermal resistance, θCS is
the case-to-sink thermal resistance (thermal compound),
and
θ
SA is the sink-to-ambient thermal resistance.
Once the maximum power dissipation is calculated from
Equation (2) above, the minimum heat sink thermal resis-
tance can be calculated from
Equation (4) below.
θ
SA = [(TJMAX –TAMB)– PDMAX (θJC + θCS)]/PDMAX (4)
Example:
V
CC = +22V
R
L = 8
θ
JC = 1C/W
θ
CS = 0.5C/W
(1) P
DMAX = 2((22V)
2/2
π2(8)) = 6W
(2)
θ
SA = [(150C– 25C) – 6W(1C/W + 0.5C/W)]/6W =
19C/W
Therefore, the minimum heat sink thermal resistance re-
quired is 19C/W for both channels being driven simulta-
neously at maximum power dissipation into an 8
load using
a +22V voltage supply. Again, remember to take into account
the unregulated supply voltage and reactive load impedance
dips.
Should it be necessary to isolate the tab of the IC from the
heat sink, an insulating washer can be used. There are many
different types of insulating washers with varying thermal re-
sistances. Good washers can be obtained from Thermalloy
or Berquist. Refer to the References list for contact informa-
tion for these manufacturers.
Supply Bypassing
The LM4753 has good power supply rejection, however, for
all power amplifiers, proper power supply bypassing is re-
quired. To prevent oscillations and instability, all op amps
and power op amps should have their supply leads by-
passed with low-inductance capacitors having short leads.
All high frequency bypass capacitors should be located as
close to the package terminals as possible and have a clear
unobstructed current return path to ground. It is typical to use
capacitor values that are a factor of 100 different from each
other to minimize interaction with each other. The LM4753
should be bypassed with 0.1 F ceramic and 100 F tanta-
lum capacitors for optimum performance. The 100 F tanta-
lum can be replaced with an electrolytic, but the bypassing
DS100043-31
FIGURE 7. Thermal Shutdown Response
DS100043-32
FIGURE 8. Thermal Model
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM4755MWC | 11 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4755MDC | 11 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4766MDC | 40 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4766MWC | 40 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4801MH/NOPB | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4755 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 11W Audio Power Amplifier with Mute |
| LM4755_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 11W Audio Power Amplifier with Mute |
| LM4755T | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 11W Audio Power Amplifier with Mute |
| LM4755T/NOPB | 功能描述:IC AMP AUDIO PWR 11W AB TO220-9 RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4755T/NOPB | 制造商:Texas Instruments 功能描述:Audio Power Amplifier IC |
發布緊急采購，3分鐘左右您將得到回復。