- 您現在的位置：買賣IC網 > PDF目錄30751 > LM4730TA/NOPB (NATIONAL SEMICONDUCTOR CORP) 14 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 PDF資料下載
參數資料
| 型號： | LM4730TA/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 14 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| 封裝： | PLASTIC, TO-220, 15 PIN |
| 文件頁數： | 5/17頁 |
| 文件大小： | 647K |
| 代理商： | LM4730TA/NOPB |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Application Information (Continued)
To achieve a transient free power-up and power-down, the
voltage seen at the input terminals should be ideally the
same. Such a signal will be common-mode in nature, and
will be rejected by the LM4730. In Figure 3, the resistor R
INP
serves to keep the inputs at the same potential by limiting the
voltage difference possible between the two nodes. This
should significantly reduce any type of turn-on pop, due to an
uneven charging of the amplifier inputs. This charging is
based on a specific application loading and thus, the system
designer may need to adjust these values for optimal perfor-
mance.
As shown in Figure 3, the resistors labeled R
BI help bias up
the LM4730 off the half-supply node at the emitter of the
2N3904. But due to the input and output coupling capacitors
in the circuit, along with the negative feedback, there are two
different values of R
BI, namely 10 k
and 200 k. These
resistors bring up the inputs at the same rate resulting in a
popless turn-on. Adjusting these resistors values slightly
may reduce pops resulting from power supplies that ramp
extremely quick or exhibit overshoot during system turn-on.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components is required to meet
the design targets of an application. The choice of external
component values that will affect gain and low frequency
response are discussed below.
The gain of each amplifier is set by resistors R
f and Ri for the
non-inverting configuration shown in Figure 1. The gain is
found by Equation (4) below:
A
V =1+Rf /Ri (V/V)
(4)
For best noise performance, lower values of resistors are
used. A value of 1k
is commonly used for R
i and then
setting the value of R
f for the desired gain. For the LM4730
the gain should be set no lower than 10V/V and no higher
than 50V/V. Gain settings below 10V/V may experience
instability and using the LM4730 for gains higher than 50V/V
will see an increase in noise and THD.
The combination of R
pass filter. The low frequency response is determined by
these two components. The -3dB point can be found from
Equation (5) shown below:
f
i =1/(2
πR
iCi) (Hz)
(5)
If an input coupling capacitor is used to block DC from the
inputs as shown in Figure 4, there will be another high pass
filter created with the combination of C
IN and RIN. When
using a input coupling capacitor R
IN is needed to set the DC
bias point on the amplifier’s input terminal. The resulting
-3dB frequency response due to the combination of C
IN and
R
IN can be found from Equation (6) shown below:
f
IN =1/(2
πR
INCIN) (Hz)
(6)
PHYSICAL IC MOUNTING CONSIDERATIONS
Mounting of the TO-220 package to a heat sink must be
done such that there is sufficient pressure from the mounting
screw to insure good contact with the heat sink for efficient
heat flow. Over tightening the mounting screw will cause the
TO-220 package to warp reducing contact area with the heat
sink. Less contact with the heat sink will increase the thermal
resistance from the TO-220 package case to the heat sink
(
θ
CS) resulting in higher operating die temperatures and
possible unwanted thermal shut down activation. Extreme
over tightening of the mounting screw will cause severe
physical stress resulting in cracked die and catastrophic IC
failure. The recommended maximum mounting screw torque
is 40 inch-lbs or 3.3 foot-lbs (4.5 newton-meter).
Additionally, if the mounting screw is used to force the TO-
220 package into correct alignment with the heat sink, pack-
age stress will be increased. This increase in package stress
will result in reduced contact area with the heat sink increas-
ing die operating temperature and possible catastrophic IC
failure.
LM4730
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM4731TA/NOPB | 25 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| LM4752MDC | 7 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4752MWC | 7 W, 2 CHANNEL, AUDIO AMPLIFIER, UUC |
| LM4752T/NOPB | 7 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM7 |
| LM4753T | 11.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4731 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 25W Audio Power Amplifier with Mute and Standby Modes |
| LM4731TA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 25W Audio Power Amplifier with Mute and Standby Modes |
| LM4731TA/NOPB | 功能描述:IC AMP AUDIO PWR 25W AB TO220-15 RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4731TA/NOPB | 制造商:Texas Instruments 功能描述:Audio Power Amplifier IC |
| LM4732 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 50W Audio Power Amplifier with Mute |
發布緊急采購，3分鐘左右您將得到回復。