- 您現在的位置：買賣IC網 > PDF目錄98001 > LM40CIMT/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO14 PDF資料下載
參數資料
| 型號： | LM40CIMT/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封裝： | MO-153AB, TSSOP-14 |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 369K |
| 代理商： | LM40CIMT/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
2.0 Register Set (Continued)
Temperature Data Format (Continued)
Temperature
Binary
Hex
- 40 C
11 1011 0000
2B0h
-255.5 C
10 0000 0001
201h
-256 C
10 0000 0000
200h
2.9.4 Temperature Control (Addr: 001 010; 0Ah)
This register is set to the reset value by a Device Reset.
Reg
Add
Register
Name
R/
W
P
O
R
Val
Bit
15
MSb
Bit
14
Bit
13
Bit
12
Bit
11
Bit
10
Bit
9
Bit
8
Bit
7
Bit
6
Bit
5
Bit
4
Bit
3
Bit
2
Bit
1
Bit
0
LSb
001 010
Temperature
Control
R/
W
0h
Reserved
EN2 EN1 EN0 ATE
000000000000
Bit
Type
Description
0
R/W
ATE (Attention Enable). When set, this bit enables an Attention Request signal to be generated by the
LM40, if the EN0, EN1 or EN2 bits of this register are set.
0: Attention Request disabled (from enabled Temperature Sensor- default)
1: Attention Request enabled (from enabled Temperature Sensor)
1
R/W
EN0 (Enable Sensor 0). When this bit is set, the Local Temperature Sensor is enabled for temperature
measurements.
0: Temperature Sensor disabled (default)
1: Temperature Sensor enabled
2
R/W
EN1 (Enable Sensor 1). When this bit is set, the Remote Thermal Diode 1 Temperature Sensor is enabled
for temperature measurements.
0: Temperature Sensor disabled (default)
1: Temperature Sensor enabled
3
R/W
EN2 (Enable Sensor 2). When this bit is set, the Remote Thermal Diode 2 Temperature Sensor is enabled
for temperature measurements.
0: Temperature Sensor disabled (default)
1: Temperature Sensor enabled
15-4
RO
Reserved. Will always read "0".
2.10 VOLTAGE-ONLY MEASUREMENT FUNCTION (TYPE 0010)
This section defines the register structure and operation of the Voltage-Only Measurement Function. The FuncDescriptor value
of this function is ‘0010’.
2.10.1 Operation
The Voltage-Only measurement function is capable of measuring the voltage of voltage measurement points ("sensors"). These
may be general or dedicated inputs (e.g., for backup battery measurement or the supply voltage to the device). The measurement
of all the enabled voltage sensors is cyclic and continuous.
Sensor Scan
The control register of the function defines which voltage sensors (inputs) are included in the scan. A sensor is
scanned only if it is enable by the Sensor Enable bit (EN0, EN1, EN2, EN3 and EN4). The sensors are scanned in an ascending,
round-robin order, based on the sensor number. Disabled sensors are skipped and the next enabled sensor in ascending order
is scanned.
The minimum scan rate is recommended to be 4Hz (i.e., the measurement data is updated at least once in 250 ms), see Section
2.11 for further details. In Low-Power Mode, the scan rate is four times lower than the scan rate in Active Mode. The scan rate
effects the bus bandwidth required to read the results. The sampling rate of the voltage measurements can also be controlled via
the Conversion Rate register, see Section 2.11 for further details.
Data Readout
When a new result is stored in the readout register a Function Event is generated. Reading the Readout register
clears the Status Function 2 flag (SF2) for the Voltage-Only Measurement Function in the Device Status register. The result is
available in the Readout register waiting for the master to read it during the master sensor read sequence. The device should
delay or buffer additional conversions to allow the master time to read the result (see Sensor Scan Rate Section 2.11). If a new
LM40
www.national.com
21
相關PDF資料 |
PDF描述 |
|---|---|
| LM4121AI1.2MWA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.25 V, UUC |
| LM4121AI1.2MDA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.25 V, UUC |
| LM4121AIADJMWA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.216 V, UUC |
| LM5000-3MTCX/NOPB | 2.7 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO16 |
| LM5010AHMH | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM40CIMTX/NOPB | 功能描述:IC HARDWARE MONITOR 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| LM40F1WE26-A | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, AMBER, 1W, Lamp Base Type:Medium Screw / E26, LED Co |
| LM40F1WE26-B | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, BLUE, 1W, Lamp Base Type:Medium Screw / E26, LED Col |
| LM40F1WE26-G | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, GREEN, 1W, Lamp Base Type:Medium Screw / E26, LED Color:Green, Bulb Size:G-40, Power Rating:1W, Wavelength Typ:525nm, Average Bulb Life:240h, Supply Voltage:240V, Current Rating:100mA, Beam Divergence:360, RoHS Compliant: Yes |
| LM40F1WE26-R | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, RED, 1W, Lamp Base Type:Medium Screw / E26, LED Color:Red, Bulb Size:G-40, Power Rating:1W, Wavelength Typ:629nm, Average Bulb Life:240h, Supply Voltage:240V, Current Rating:100mA, Beam Divergence:360 , RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。