- 您現在的位置：買賣IC網 > PDF目錄358861 > LM40 (National Semiconductor Corporation) Hardware Monitor with Dual Thermal Diodes and SensorPath Bus PDF資料下載
參數資料
| 型號： | LM40 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Hardware Monitor with Dual Thermal Diodes and SensorPath Bus |
| 中文描述： | 硬件監控雙熱二極管和SensorPath總線 |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 369K |
| 代理商： | LM40 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
1.0 Functional Description
(Continued)
All devices (master or slave) must monitor the bus for an
Attention Request signal. The following notes clarify the
intended system operation that uses the Attention Request
Indication.
Masters are expected to use the attention request as a
trigger to read results from the LM40. This is done in a
sequence that covers all LM40s. This sequence is re-
ferred to as "master sensor read sequence".
After an Attention Request is sent by an LM40 until after
the next read from the Device Status register the LM40
does not send Attention Requests for a function event
since it is guaranteed that the master will read the Status
register as part of the master sensor read sequence.
Note that the LM40 will send an attention for BER, re-
gardless of the Status register read, to help the master
with any error recovery operations and prevent dead-
locks.
A master must record the Attention Request event. It
must then scan all slave devices in the system by reading
their Device Status register and must handle any pending
event in them before it may assume that there are no
more events to handle.
Note: there is no indication of which slave has sent the
request. The requirement that multiple requests are not sent
allows the master to know within one scan of register reads
that there are no more pending events.
1.3.6 Fixed Device Number Setting
The LM40 device number is defined by strapping of the ADD
pin. The LM40 will wake (after Device Reset) with the Device
Number field of the Device Number register set to the ad-
dress as designated in
Section 2.3
"Device Number". It is the
responsibility of the system designer to avoid having two
devices with the same Device Number on the bus.
Devices should be detected by the master by a read opera-
tion of the Device Number register. The read returns "000" if
there is no device at that address on the bus (the EP bit must
be ignored).
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM4120AIM5X-5.0 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-1.8 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-3.3 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-2.5 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-3.3 | Precision Micropower Low Dropout Voltage Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM400 | 制造商:LM TECHNOLOGIES 功能描述:MODULE BLUETOOTH V2.0 CLASS 1 BC04 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MODULE, BC04, CLASS 1, EDR 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MOD, PDA, GPS, POS, BC04, CLASS 1, EDR; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Data Rate:3Mbps; Bluetooth Version:Bluetooth 2.0 + EDR; Bluetooth Class:Class 1; Receive Sensitivity:-88dBm; Type:Bluetooth Module ;RoHS Compliant: Yes |
| LM4001 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4001G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
| LM4002 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4002G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
發布緊急采購，3分鐘左右您將得到回復。