- 您現在的位置：買賣IC網 > PDF目錄358850 > LM3822MM-2.0 (NATIONAL SEMICONDUCTOR CORP) Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output PDF資料下載
參數資料
| 型號： | LM3822MM-2.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 265K |
| 代理商： | LM3822MM-2.0 |
PWM Output and Current
Accuracy
Offset
The PWM output is quantized to 1024 levels. Therefore, the
duty cycle can change only in increments of 1/1024.
There is a one-half (0.5) quantization cycle delay in the out-
put of the PWM circuitry. That is to say that instead of a duty
cycle of N/1024, the duty cycle actually is (N+
1
2
)/1024.
The quantization error can be corrected for if a more precise
result is desired. To correct for this error, simply subtract
1/2048 from the measured duty cycle.
The extra half cycle delay will show up as a DC offset of
1
2
bit if it is not corrected for. This is approximately 1.0 mA for
1.0 Amp parts, and 10 mA for 2.0 Amp parts.
Jitter
In addition to quantization, the duty cycle will contain some
jitter. The jitter is quite small (for example, the standard de-
viation of jitter is only 0.1% for the LM3822-1.0). Statistically
the jitter can cause an error in a current sample. Because the
jitter is a random variable, the mean and standard deviation
are used. The mean, or average value, of the jitter is zero.
The standard deviation (0.1%) can be used to define the
peak error caused from jitter.
The “crest factor” has often been used to define the maxi-
mum error caused by jitter. The crest factor defines a limit
within which 99.7% of the samples fall. The crest factor is de-
fined as
±
0.3% error in the duty cycle.
Since the jitter is a random variable, averaging multiple out-
puts will reduce the effective jitter. Obeying statistical laws,
the jitter is reduced by the square root of the number of read-
ings that are averaged. For example, if four readings of the
duty cycle are averaged, the resulting jitter (and crest factor)
are reduced by a factor of two.
Jitter and Noise
Jitter in the PWM output appears as noise in the current
measurement. The Electrical Characteristics show noise
measured in current RMS (root mean square).Arbitrarily one
could specify PWM jitter, as opposed to noise. In either case
the effect results in a random error in an individual current
measurement.
Noise, just like jitter, can be reduced by averaging many
readings. The RMS value of the noise corresponds to one
standard deviation. The “crest factor” can be calculated in
terms of current, and is equal to
±
3 sigma (RMS value of the
noise).
Noise will also be reduced by averaging multiple readings,
and follows the statistical laws of a random variable.
Accuracy versus Noise
The graph shown in Figure 5 illustrates the typical response
of
±
1 Ampere current gauges. In this graph, the horizontal
axis indicates time, and the vertical axis indicates measured
current (the PWM duty cycle has been converted to current).
The graph was generated for an actual current of 500 mA.
The difference between successive readings manifests itself
as jitter in the PWM output or noise in the current measure-
ment (when duty cycle of the PWM output is converted to
current).
The accuracy of the measurement depends on the noise in
the current waveform. The accuracy can be improved by av-
eraging several outputs. Although there is variation in suc-
cessive readings, a very accurate measurement can be ob-
tained by averaging the readings. For example, on
averaging the readings shown in this example, the average
current measurement is 502.3 mA (Figure 5). This value is
very close to the actual value of 500 mA. Moreover, the ac-
curacy depends on the number of readings that are
averaged.
Low Current Measurements
The DC offset of the LM3822-1.0 is typically under 1 mA.
This low offset allows accurate low current measurements.
Even currents in the 10 mA range can be measured with ac-
curacies typically better than
±
5%.
DS101249-26
FIGURE 5. Typical Response of LM3822
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM3822MMX-2.0 | Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| LM3822MMX-1.0 | Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| LM3822 | Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| LM3842A | CURRENT MODE PWM CONTROLLER |
| LM385BZBG | CAP 39PF 200V 5% NP0(C0G) AXIAL RAD.20 BULK R-MIL-PRF-20 STANDOFF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3822MMX-1.0 | 功能描述:IC CURRENT GAUGE PRECISION 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| LM3822MMX-2.0 | 功能描述:IC CURRENT GAUGE PRECISION 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| LM3824 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| LM3824MM-1.0 | 制造商:Texas Instruments 功能描述:Battery Charger 8-Pin MSOP Rail 制造商:Texas Instruments 功能描述:IC CURRENT GAUGE FAST SMD MSOP8 |
| LM3824MM-1.0/NOPB | 功能描述:IC CURRENT GAUGE 3% 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。