參數資料
型號: LM3722E4.63MWC
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
封裝: WAFER
文件頁數: 24/24頁
文件大?。?/td> 398K
代理商: LM3722E4.63MWC
Applications Information (Continued)
TABLE 1. Monitored Tolerance Table
Reset
Threshold
Supply Voltage
2.5V
3.3V
5.0V
4.63 ± %
90.8-94.4%
3.08 ± %
91.8-95.2%
2.32 ± %
90.8-94.8%
Ensuring a Valid Reset Output Down to V
CC =0V
When V
CC falls below 1V, the LM3722 RESET output is
unable to sink the rated current. A high-impedance CMOS
logic input connected to RESET can therefore drift to unde-
termined voltages. To prevent this situation, a 100k
resistor
should be connected from the RESET output to ground, as
shown in
A 100k
pull-up resistor to V
CC is also recommended for the
LM3723, if RESET is required to remain valid for V
CC < 1V.
Open Drain Output (LM3724)
An open drain output allows easy paralleling of multiple
microprocessor reset circuits without requiring additional
logic gates. Open drain outputs also allow interfacing de-
vices of differing logic levels or families, since the output
pull-up resistor may be connected to any supply voltage up
to 5.5V, regardless of LM3724 V
CC.
The pull up resistor is calculated so that maximum current
flow into RESET is less than 10 mA when activated. The
resistor must be small enough so that the leakage current of
all connected devices does not create an excessive voltage
drop when the output is not activated. A resistor value of 100
k
will generally suffice.
Negative-Going V
CC Transients
The LM3722/LM3723/LM3724 are relatively immune to short
negative-going transients or glitches on V
CC. Figure 2 shows
the maximum pulse width a negative-going V
CC transient
can have without causing a reset pulse. In general, as the
magnitude of the transient increases, going further below the
threshold, the maximum allowable pulse width decreases.
Typically, a V
CC transient that goes 125 mV below the reset
threshold and lasts 40 s or less will not cause a reset pulse.
A 0.1 F bypass capacitor mounted as close as possible to
the V
CC pin will provide additional transient rejection.
Interfacing to Ps with Bidirectional Reset Pins
Microprocessors with bidirectional reset pins, such as the
Motorola 68HC11 series, can be connected to the LM3722
RESET output. To ensure a correct output on the LM3722
even when the microprocessor reset pin is in the opposite
state, connect a 4.7k
resistor between the LM3722 RESET
output and the P reset pin, as shown in
Figure 3. Buffer the
LM3722 RESET output to other system components.
20014410
FIGURE 1. Circuit for RESET Valid from V
CC =0V
20014414
FIGURE 2. Maximum Transient Duration without
Causing a Reset Pulse vs. Reset Comparator
Overdrive
LM3722/LM3723/LM3724
www.national.com
9
相關PDF資料
PDF描述
LM3724I2.32MWC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3722E3.08MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3724I2.32MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3722I2.32MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3723I3.08MWC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
相關代理商/技術參數
參數描述
LM3722EM5-2.32 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD SOT23-5 3722
LM3722EM5-2.32/NOPB 功能描述:IC MPU SUPERVISR 2.32V SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR
LM3722EM5-3.08 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD SOT23-5 3722
LM3722EM5-3.08/NOPB 功能描述:IC MPU SUPERVISR 3.08V SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR
LM3722EM5-4.63 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD SOT23-5 3722