參數資料
型號: LM3622-8.2MWC
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩(wěn)壓器
英文描述: BATTERY CHARGE CONTROLLER, UUC
封裝: WAFER
文件頁數: 10/13頁
文件大小: 253K
代理商: LM3622-8.2MWC
Functional Description
The simplified LM3622 block diagram in
Figure 1 gives a
general idea of the circuit operation. The controller integrates
the reference, feedback and drive functions on-chip to con-
trol a linear, lithium-ion battery charger in constant voltage
and constant current (CVCC) charge operation. The regu-
lated output voltage is sensed between CEL and CS, and the
battery charge current is sensed across a current-sense re-
sistor between CS and GND. The EXT pin is designed for
driving a series pass element, which can be a PNP transistor
or a P-MOSFET.
Tying the LV
ENB
pin to ground enables the controller’s
low-voltage detection circuit. When the low-voltage detection
circuit is enabled and a battery voltage below a preset
threshold is detected, the LM3622 will drive the LV pin low
and shut off the current flowing into the EXT pin to suspend
the CVCC charge process. The low-voltage threshold is user
selectable to be either 2.15V/cell or 2.7V/cell by pulling the
LV
SEL pin to GND or VCC respectively. The LV pin is a NPN
open collector output that can be used to turn on a low cur-
rent source to wake up charge a deeply depleted battery.
When the low-voltage detection is disabled (LV
ENB pulled up
to V
CC), the LM3622 always starts the charge cycle in con-
stant current mode at any battery voltage below the control-
ler’s regulation level, and maintains the LV pin at a
high-impedance state.
Application Information
CEL Pin Current Drain
The LM3622 has an internal power down switch in series
with the on-chip resistor divider that is used for sensing the
battery voltage. In the event that the V
CC supply is removed,
the power down switch will disconnect the resistor divider
from the CS pin, preventing the battery from discharging
through the CEL pin.
EXT Pin
The EXT pin is internally pulled up to V
CC via a 20A current
source making it possible to eliminate the external
base-emitter resistor when driving a PNP transistor, or the
gate-source resistor when driving a P-MOSFET. However,
the voltage applied to EXT is not allowed to be higher than
(V
CC + 0.3V), otherwise the reverse current from EXT pin to
V
CC pin may cause damage to the device.
LV Pin Current Rating
The LV pin is a low power, NPN open collector output that is
rated to sink 10mA maximum. Therefore, the value of the pull
up resistor should be chosen high enough to limit the current
to be less than 10mA.
CS Pin
In normal operation, the current limit threshold voltage for
the CS pin is 100mV typical. In case of a fault condition, the
voltage to this pin should be limited to below 5V.
DS100974-11
FIGURE 1. LM3622 Simplified Block Diagram
LM3622
www.national.com
6
相關PDF資料
PDF描述
LM3622-4.2MDC BATTERY CHARGE CONTROLLER, UUC
LM3641MX POWER SUPPLY MANAGEMENT CKT, PDSO8
LM3647IMX 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20
LM3655TLX 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA25
LM3661TLX-1.40 0.65 A SWITCHING REGULATOR, 675 kHz SWITCHING FREQ-MAX, PBGA10
相關代理商/技術參數
參數描述
LM3622AM-4.1 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Lithium-Ion Battery Charger Controller
LM3622AM-4.1/NOPB 功能描述:IC CTRLR LI-ION BAT CHRG 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子(Li-Ion)、鋰聚合物(Li-Pol) 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
LM3622AM-4.2 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Lithium-Ion Battery Charger Controller
LM3622AM-4.2/NOPB 功能描述:IC CTRLR LI-ION BAT CHRG 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子(Li-Ion)、鋰聚合物(Li-Pol) 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
LM3622AM-8.1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management