- 您現在的位置：買賣IC網 > PDF目錄30747 > LM334ZT (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBCY3 PDF資料下載
參數資料
| 型號： | LM334ZT |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBCY3 |
| 封裝： | PLASTIC, TO-92, 3 PIN |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 1037K |
| 代理商： | LM334ZT |
LM134 - LM234 - LM334
5/11
APPLICATION HINTS
SLEW RATE
At slew rates above a threshold (see curve) the
LM134, LM234, LM334 can have a non-linear cur-
rent characteristic. The slew rate at which this
takes place is directly proportional to Iset. At Iset =
10A, dv/dt max. = 0.01V/s ; at Iset = 1mA, dv/dt
max. = 1V/s. Slew rates of more than 1V/s do
not damage the circuit nor do they produce high
currents.
THERMAL EFFECTS
Internal heating can have a significant effect on
current regulation for an Iset above 100A. For ex-
ample, each increase of 1V in the voltage across
the LM134 at Iset = 1mA will increase the junction
temperature by
≈ 0.4°C (in still air). The output
current (Iset) has a temperature coefficient of
about 0.33%/°C. Thus the change in current due
to the increase in temperature will be (0.4) (0.33) =
0.132%. This is degradation of 10 : 1 in regulation
versus the true electrical effects. Thermal effects
should be taken into account when d.c. regulation
is critical and Iset is higher than 100A.
SHUNT CAPACITANCE
In certain applications, the 15pF value for the
shunt capacitance should be reduced :
u because of loading problems,
u because of limitation of output impedance
of the current source in a.c. applications.
This reduction of capacitance can be easily
carried out by adding a FET as indicated in
the typical applications.
The value of this capacitance can be reduced by
at least 3pF and regulation can be improved by an
order of magnitude without any modifications of
the d.c. characteristics (except for the minimum in-
put voltage).
NOISE
The current noise produced by LM134, LM234,
LM334 is about 4 times that of a transistor. If the
LM134, LM234, LM334 is used as an active load
for a transistor amplifier, the noise at the input will
increase by about 12dB. In most cases this is ac-
ceptable, and a single amplifier can be built with a
voltage gain higher than 2000.
LEAD RESISTANCE
The sense voltage which determines the current
of the LM134, LM234, LM334 is less than 100mV.
At this level, the thermocouple effects and the
connection resistance should be reduced by locat-
ing the current setting resistor close to the device.
Do not use sockets for the ICs. A contact resis-
tance of 0.7
is sufficient to decrease the output
current by 1% at the 1mA level.
SENSING TEMPERATURE
The LM134, LM234, LM334 are excellent remote
controlled temperature sensors because their op-
eration as current sources preserves their accura-
cy even in the case of long connecting wires. The
output current is directly proportional to the abso-
lute temperature in Kelvin degrees according to
the following equation.
The calibration of the LM134, LM234, LM334 is
simplified by the fact that most of the initial accura-
cy is due to gain limitation (slope error) and not an
offset. Gain adjustment is a one point trim be-
cause the output of the device extrapolates to zero
at 0°K.
This particularity of the LM134, LM234, LM334 is
illustrated in the above diagram. Line abc repre-
sents the sensor current before adjustment and
line a’b’c’ represents the desired output. A gain
adjustment provided at T2 will move the output
from b to b’ and will correct the slope at the same
time so that the output at T1 and T3 will be correct.
This gain adjustment can be carried out by means
of Rset or the load resistor used in the circuit. After
adjustment, the slope error should be less than
1%. A low temperature coefficient for Rset is nec-
essary to keep this accuracy. A 33ppm/°C temper-
ature drift of Rset will give an error of 1% on the
slope because the resistance follows the same
temperature variations as the LM134, LM234,
LM334. Three wires are required to isolate Rset
from the LM134, LM234, LM334. Since this solu-
tion is not recommended. Metal-film resistors with
a drift less than 20ppm/°C are now available.
Wirewound resistors can be used when very high
stability is required.
Iset =
227V/°K) (T
()
Rset
-----------------------------------------
相關PDF資料 |
PDF描述 |
|---|---|
| LM336BZ-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
| LM336Z-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
| LM338N-1 | 2.2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDIP14 |
| LM3411N-3.3 | THREE TERM VOLTAGE REFERENCE, PDIP8 |
| LM3411AN-5.0 | THREE TERM VOLTAGE REFERENCE, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM335 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PRECISION TEMPERATURE SENSORS |
| LM3350 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Switched Capacitor Voltage Converter |
| LM3350AM WAF | 制造商:Texas Instruments 功能描述: |
| LM3350MM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Switched Capacitor Voltage Converter |
| LM3350MM/NOPB | 功能描述:IC REG MULTI CONFIG 50MA 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。