參數資料
型號： LM27241MTCX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： Synchronous Buck Regulator Controller for Mobile Systems
中文描述： SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20
封裝： PLASTIC, TSSOP-20
文件頁數： 18/27頁
文件大?。?/td> 1336K
代理商： LM27241MTCX
Application Information
(Continued)
FREQUENCY SET RESISTOR (TYPICAL VALUE)
R
FREQ
(
)
30100
25500
22100
16200
15000
12700
12400
10000
8660
7500
Frequency (kHz)
226
261
300
388
411
485
510
630
720
820
LAYOUT GUIDELINES
For a deeper understanding of Buck converters and the
‘critical traces’please seeApplication NoteAN-1229 at http://
power.national.com .
Figure 15
is based on such an understanding of the critical
sections and also the pin functions of the LM27241. Refer to
the Typical Applications circuit and the LM27241 TSSOP
pinouts to understand the layout suggestions more thor-
oughly.
The components shown in
Figure 15
are most critical and
must be placed with the following guidelines.
There are three separate Ground shapes on the top layer,
and one ground plane that is either on the bottom layer, or on
an internal layer. The ground shapes are connected to the
ground plane through vias.
Input Capacitor Ground Shape: This ground shape connects
the input capacitors and the source of the synchronous
MOSFET (Q2). This ground shape contains high
i/
t cur-
rent waveforms. Therefore effort should be taken to keep
sensitive ground connections away from this ground shape.
The input capacitors should be placed as close as possible
to the MOSFET, and the vias to the ground plane should be
as close to the capacitors ground pad as possible. Ensure
that this ground plane shape is not directly connected to the
Output Capacitors Ground Shape. Note that the current limit
detector circuit compares the voltage on the ILIM pin with
respect to the PGND pin. Therefore, if the power ground is
noisy it can lead to erroneous triggering of the current limit
detector. This will manifest itself as an inability to meet the
load requirement despite over sizing the current limit resis-
tor. It can also lead to failure of the output to recover after
encountering an overload condition. Connect the LM27241
PGND pin to this shape, and place two vias from the pin pad
to the ground plane.
Output Capacitor Ground Shape: The Output Capacitor
Ground Shape should be large as possible. Place the vias
that connect this shape to the ground plane as close to the
capacitor pads as possible.
SGND Ground Shape: A small ground shape should be
created so that all noise sensitive components such as the
lower feedback resistor, V
supply capacitor, frequency
adjust resistor and SKIP/FPWM Mode select resistor can be
connected to. Two to three vias should connect this ground
shape to the ground plane. Place all the components men-
tioned as close as possible to the controller. Route the
feedback resistors from Vout to the controller as far away
from the MOSFETs and SW-node as possible.
SW-Node Shape: This shape connects the top MOSFET
source to the synchronous MOSFET drain, and then con-
nects to the output inductor. This shape should be kept small
due to the high frequency content found at this node.
Enough copper area must be left around the MOSFET for
thermal dissipation. More details on this are also provided in
AN-1229.
HDRV & LDRV connections: Try to keep the trace lengths
from the controller to the gate of the MOSFET as short as
possible. Both these traces contain fast rise and fall times,
and low inductance trace lengths should be maintained.
C
V5
& C
VDD
Capacitors: These two capacitors should be
placed very close to the controller and their respective pins
for best performance.
20120190
FIGURE 14. Frequency Adjust Resistor Guideline
20120143
FIGURE 15. Critical Component placement (TSSOP)
L
www.national.com
18
相關PDF資料
PDF描述
LM2746 Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
LM2746MXA Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
LM2746MXAX Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
LM2753SD High Power Switched Capacitor Voltage Convertor/Flash LED Driver
LM2753 High Power Switched Capacitor Voltage Convertor/Flash LED Driver
相關代理商/技術參數
參數描述
LM27241MTCX/NOPB 功能描述:IC REG CTRLR BUCK PWM VM 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF)
LM27243A E WAF 制造商:Texas Instruments 功能描述:
LM2724A 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed 3A Synchronous MOSFET Driver
LM2724ALD 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed 3A Synchronous MOSFET Driver
LM2724ALD/NOPB 功能描述:IC DRIVER MOSFET DUAL SYNC 8-LLP RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:低端 輸入類型:非反相 延遲時間:40ns 電流 - 峰:9A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:4.5 V ~ 35 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*