- 您現在的位置：買賣IC網 > PDF目錄98000 > LM2710MTX-ADJ/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.4 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LM2710MTX-ADJ/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.4 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | TSSOP-20 |
| 文件頁數： | 14/20頁 |
| 文件大小： | 853K |
| 代理商： | LM2710MTX-ADJ/NOPB |
Pin Functions
V
SW(Pin 1): This is the drain of the internal NMOS power
switch. Minimize the metal trace area connected to this pin to
minimize EMI.
V
IN(Pin 2): Input Supply Pin. Bypass this pin with a capacitor
as close to the device as possible. The capacitor should
connect between V
IN and GND.
SHDN(Pin 3): Shutdown Pin. The shutdown pin signal is
active low. A voltage of less than 0.3V disables the device. A
voltage greater than 0.85V enables the device.
FSLCT(Pin 4): Frequency Select Pin. Connecting FSLCT to
AGND selects a 600 kHz operating frequency for the switch-
ing regulator. Connecting FSLCT to V
IN selects a 1.25 MHz
operating frequency. If FSLCT is left floating, the switching
frequency defaults to 600 kHz.
Vs+(Pin 5): Supply pin for the Vcom buffer and the four
Gamma buffers. Bypass this pin with a capacitor as close to
the device as possible. The capacitor should connect be-
tween Vs+ and GND.
Vcom-in(Pin 6): Vcom Buffer input pin.
GMA1-in(Pin 7): Gamma Buffer input pin.
GMA2-in(Pin 8): Gamma Buffer input pin.
GMA3-in(Pin 9): Gamma Buffer input pin.
GMA4-in(Pin 10): Gamma Buffer input pin.
GMA4-out(Pin 11): Gamma Buffer output pin.
GMA3-out(Pin 12): Gamma Buffer output pin.
GMA2-out(Pin13): Gamma Buffer output pin.
GMA1-out(Pin 14): Gamma Buffer output pin.
Vcom-out(Pin 15): Vcom Buffer output pin.
SS(Pin 16): Softstart pin. Connect capacitor to SS pin and
AGND to slowly ramp inductor current on startup.
V
C(Pin
17): Compensation Network for Boost switching
regulator. Connect resistor/capacitor network between V
C
pin and AGND for boost switching regulator AC compensa-
tion.
FB(Pin 18): Feedback pin. Set the output voltage by select-
ing values of R1 and R2 using:
Connect the ground of the feedback network to the AGND
plane, which can be tied directly to the GND pin.
AGND(Pin 19): Analog ground pin. Ground connection for
the Vcom buffer, Gamma buffers and the boost switching
regulator. AGND must be tied directly to GND at the pins.
GND(Pin 20): Power ground pin. Ground connection for the
NMOS power device of the boost switching regulator. GND
must be tied directly to AGND at the pins.
Ordering Information
Order Number
Package Type
NSC Package Drawing
Supplied As
LM2710MT-ADJ
TSSOP-20
MTC20
73 Units, Rail
LM2710MTX-ADJ
TSSOP-20
MTC20
2500 Units, Tape and Reel
LM2710
www.national.com
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM2710MT-ADJ/NOPB | 1.4 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM2984MDC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC |
| LM3207TL/NOPB | 1.2 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PBGA9 |
| LM3218SE | SWITCHING REGULATOR, DSO8 |
| LM3350MWC | SWITCHED CAPACITOR CONVERTER, 1100 kHz SWITCHING FREQ-MAX, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2711 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT Panel Module |
| LM2711A-ADJ WAF | 制造商:Texas Instruments 功能描述: |
| LM2711MT-ADJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT Panel Module |
| LM2711MTX-ADJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT Panel Module |
| LM2715 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT Panel Module |
發布緊急采購，3分鐘左右您將得到回復。