- 您現在的位置：買賣IC網 > PDF目錄98000 > LM26480QSQX-CF/NOPB (NATIONAL SEMICONDUCTOR CORP) 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 PDF資料下載
參數資料
| 型號： | LM26480QSQX-CF/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| 封裝： | 4 X 4 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, LLP-24 |
| 文件頁數： | 20/30頁 |
| 文件大?。?/td> | 2455K |
| 代理商： | LM26480QSQX-CF/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Board Layout Considerations
PC board layout is an important part of DC-DC converter de-
sign. Poor board layout can disrupt the performance of a DC-
DC converter and surrounding circuitry by contributing to EMI,
ground bounce, and resistive voltage loss ii the traces. These
can send erroneous signals to the DC-DC converter IC, re-
sulting in poor regulation or instability. Poor layout can also
result in re-flow problems leading to poor solder joints, which
can result in erratic or degraded performance.
Good layout for the LM26480 bucks can be implemented by
following a few simple design rules, as illustrated in Figure
3.
30040468
FIGURE 3. Board Layout Design Rules for the LM26480
1.
Place the buck inductor and filter capacitors close
together and make the trace short. The traces between
these components carry relatively high switching
currents and act as antennas. Following this rule reduces
radiated noise. Place the capacitors and inductor close
to the buck.
2.
Arrange the components so that the switching current
loops curl in the same direction. During the first halt of
each cycle, current flows from the input filter capacitor,
through the buck and inductor to the output filter
capacitor and back through ground, forming a current
loop. In the second half of each cycle, current is pulled
up from ground, through the buck by the inductor, to the
output filter capacitor and then back through ground,
forming a second current loop. Routing these loops so
the current curls in the same direction prevents magnetic
field reversal between the two half-cycles and reduces
radiated noise.
3.
Connect the ground pins of the buck, and filter capacitors
together using generous component-side copper fill as a
pseudo-ground plane. Then connect this to the ground-
plane (if one is used) with several vias. This reduces
ground—plane noise by preventing the switching
currents from circulating through the ground plane. it also
reduces ground bounce at the buck by giving it a low-
impedance ground connection.
4.
Use wide traces between the power components and for
power connections to the DC-DC converter circuit. This
reduces voltage errors caused by resistive losses across
the traces
5.
Rout noise sensitive traces, such as the voltage
feedback path, away from noisy traces between the
power components. The voltage feedback trace must
remain close to the buck circuit and should be routed
directly from FB to VOUT at the output capacitor and
should be routed opposite to noise components. This
reduces EMI radiated onto the DC-DC converter’s own
voltage feedback trace.
In mobile phones, for example, a common practice is to place
the DC-DC converter on one corner of the board, arrange the
CMOS digital circuitry around it (since this also generates
noise), and then place sensitive preamplifiers and IF stages
on the diagonally opposing corner. Often, the sensitive cir-
cuitry is shielded with a metal pan and power to it is post-
regulated to reduce conducted noise, using low-dropout
linear regulators.
27
www.national.com
LM26480
相關PDF資料 |
PDF描述 |
|---|---|
| LM26480QSQ-CF/NOPB | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQ-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQX-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
| LM2661M/NOPB | SWITCHED CAPACITOR CONVERTER, 80 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM2660MMX/NOPB | SWITCHED CAPACITOR CONVERTER, 40 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM26480SQ-AA | 制造商:Texas Instruments 功能描述:DC/ DC STEP DOWN, DUAL LINEAR REG, IC |
| LM26480SQ-AA/NOPB | 功能描述:線性穩壓器 - 標準 DUAL HI-CRNT STEP- DOWN DC/DC RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| LM26480SQ-AA/S7002404 | 制造商:Texas Instruments 功能描述: |
| LM26480SQ-AAEV | 功能描述:BOARD EVALUATION LM26480SQ-AA RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM26480SQ-AAEV/NOPB | 功能描述:電源管理IC開發工具 LM26480SQ-AAEV EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。