- 您現在的位置：買賣IC網 > PDF目錄44549 > LM2636MX/NOPB (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LM2636MX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | PLASTIC, SOP-20 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 372K |
| 代理商： | LM2636MX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Connection Diagrams
Pin Descriptions
LSGATE (Pin 1): Gate drive for the low-side N-channel
MOSFET. This signal is interlocked with HSGATE (Pin 20) to
avoid a shoot-through problem.
BOOTV (Pin 2): Power supply for high-side N-channel
MOSFET gate drive. The voltage should be at least one gate
threshold above the converter input voltage to properly oper-
ate the high-side N-FET.
PGND (Pin 3): Ground for high current circuitry. It should be
connected to system ground.
SGND (Pin 4): Ground for signal level circuitry. It should be
connected to system ground.
V
CC (Pin 5): Power supply for the controller.
SENSE (Pin 6): Converter output voltage sensing. It pro-
vides input for power good, fast dual comparator control
loop, and over-voltage protection circuitry. It is recom-
mended that a 0.1 F capacitor be connected between this
pin and ground to avoid potential noise problems.
IMAX (Pin 7): Current limit threshold setting. It sinks a fixed
180 A current. By connecting a resistor between the high
side MOSFET drain and this pin, a fixed voltage drop can be
built across the resistor. This voltage drop is compared with
the V
DS of the high-side N-MOSFET to determine if an over-
current condition has occurred.
IFB (Pin 8): High-side N-MOSFET source voltage sensing.
This pin is one V
DS below drain voltage. When this voltage is
lower than that of IMAX pin during the time the high-side FET
is on, it means V
DS is higher than the preset voltage across
the IMAX resistor, which can be interpreted as an over-
current condition.
V
REF (Pin 9): Bandgap reference voltage. This voltage is
mainly for use by other power supplies on the motherboard
which need a reference.
EA_OUT (Pin 10): Output of the error amplifier. The voltage
level on this pin is compared with an internally generated
ramp signal to determine the duty cycle. This pin is neces-
sary for compensating the primary control loop.
FB (Pin 11): Inverting input of the error amplifier. A pin nec-
essary for compensating the control loop.
FREQ_ADJ (Pin 12): Switching frequency adjustment.
Switching frequency can be adjusted by changing the
grounding resistance on this pin.
PWRGD (Pin 13): Power Good. There are two windows
around the DAC output voltage that are associated with
PWRGD pin, the ±10% window and the ±8% window. If
PWRGD is initially high (open drain state) and output voltage
travels out of ±10% window, PWRGD goes to low (low im-
pedance to ground). If PWRGD is initially low and output
voltage travels into the ±8% window and has stayed within
the window for at least 10 ms, PWRGD goes to high. A
PWRGD high means the output voltage is at least within the
±10% window whereas a PWRGD low indicates the output
voltage is definitely outside the ±8% window.
VID4:0 (Pins 14, 15, 16, 17, 18): Voltage Identification
Code. The five pins accept an open-ground pattern 5-bit bi-
nary code from outside the chip (typically from the CPU) for
generating the desired output voltage. Each VID pin is inter-
nally pulled up to V
CC via a 90 A current source. Table 1
shows the code table.
OUTEN (Pin 19): Output Enable. The output voltage is dis-
abled when this pin is pulled low. It is internally pulled up to
V
CC via a 90 A current source.
HSGATE (Pin 20): Gate drive for the high-side N-channel
MOSFET. This signal is interlocked with LSGATE (Pin 1) to
avoid a shoot-through problem.
TABLE 1. VID Code and DAC Output
V
ID4
V
ID3
V
ID2
V
ID1
V
ID0
Rated Output
Voltage (V)
01111
1.30
01110
1.35
01101
1.40
01100
1.45
01011
1.50
01010
1.55
01001
1.60
01000
1.65
00111
1.70
00110
1.75
00101
1.80
00100
1.85
00011
1.90
00010
1.95
00001
2.00
TOP VIEW
DS100834-3
Plastic SO-20
Order Number LM2636M
See NS Package Number M20B
TOP VIEW
DS100834-3
Plastic TSSOP-20
Order Number LM2636MTC
See NS Package Number MTC20
LM2636
www.national.com
2
相關PDF資料 |
PDF描述 |
|---|---|
| LM2636MTCX/NOPB | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM2637M/NOPB | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO24 |
| LM2637MWC | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, UUC |
| LM2639MX/NOPB | SWITCHING CONTROLLER, 8700 kHz SWITCHING FREQ-MAX, PDSO24 |
| LM2639M/NOPB | SWITCHING CONTROLLER, 8700 kHz SWITCHING FREQ-MAX, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2637 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LM2637A E WAF | 制造商:Texas Instruments 功能描述: |
| LM2637M | 制造商:OC White Company 功能描述:LDO Cntrlr REG CTRLR 1.3V to 3.5V 24-Pin SOIC W Rail |
| LM2637M/NOPB | 功能描述:IC MOTHERBRD PWR SUPPLY 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LM2637MX/NOPB | 功能描述:IC MOTHERBRD PWR SUPPLY 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。