- 您現在的位置：買賣IC網 > PDF目錄44549 > LM2622-ADJMWC (NATIONAL SEMICONDUCTOR CORP) 2.3 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, UUC PDF資料下載
參數資料
| 型號： | LM2622-ADJMWC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.3 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, UUC |
| 封裝： | WAFER |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 478K |
| 代理商： | LM2622-ADJMWC |
Operation (Continued)
The phase margin can also be improved by adding C
C2 as
discussed earlier in the section. The equation for A
DC is
given below with additional equations required for the calcu-
lation:
mc ) 0.072fs (in V/s)
where R
L is the minimum load resistance, VIN is the maxi-
mum input voltage, g
m is the error amplifier transconduc-
tance found in the
Electrical Characteristics table, and R
D-
SON
is the value chosen from the graph ’R
DSON vs. VIN ’in
the
Typical Performance Characteristics section.
Layout Considerations
The input bypass capacitor C
IN, as shown in the typical
operating circuit, must be placed close to the IC. This will
reduce copper trace resistance which effects input voltage
ripple of the IC. For additional input voltage filtering, a 100nF
bypass capacitor can be placed in parallel with C
IN, close to
the V
IN pin, to shunt any high frequency noise to ground. The
output capacitor, C
OUT, should also be placed close to the
IC. Any copper trace connections for the C
OUT capacitor can
increase the series resistance, which directly effects output
voltage ripple. The feedback network, resistors R
FB1 and
R
FB2, should be kept close to the FB pin, and away from the
inductor, to minimize copper trace connections that can in-
ject noise into the system. Trace connections made to the
inductor and schottky diode should be minimized to reduce
power dissipation and increase overall efficiency. For more
detail on switching power supply layout considerations see
Application Note AN-1149:
Layout Guidelines for Switching
Power Supplies.
LM2622
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM2630MTC-ADJ/NOPB | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM2630MTC-ADJX | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM2631MTCX-ADJ/NOPB | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM2636MWC | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, UUC |
| LM2636MX/NOPB | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2622EVAL | 功能描述:BOARD EVALUATION LM2622 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM2622MM-ADJ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2622MM-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2622MMX-ADJ | 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Up 2V to 12V 8-Pin MSOP T/R |
| LM2622MMX-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。