參數資料
型號: LM2594-ADJMWC
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
封裝: WAFER
文件頁數: 6/33頁
文件大?。?/td> 837K
代理商: LM2594-ADJMWC
LM2594/LM2594HV Series Buck Regulator Design Procedure (Adjustable
Output) (Continued)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
6. Input Capacitor (C
IN)
A low ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. In addition, the RMS
current rating of the input capacitor should be selected to be
at least 12 the DC load current. The capacitor manufacturers
data sheet must be checked to assure that this current rating
is not exceeded. The curve shown in
Figure 13 shows typical
RMS current ratings for several different aluminum electro-
lytic capacitor values.
This capacitor should be located close to the IC using short
leads and the voltage rating should be approximately 1.5
times the maximum input voltage.
If solid tantalum input capacitors are used, it is recomended
that they be surge current tested by the manufacturer.
Use caution when using ceramic capacitors for input bypass-
ing, because it may cause severe ringing at the V
IN pin.
For additional information, see section on input capaci-
tors in application information section.
6. Input Capacitor (C
IN)
The important parameters for the Input capacitor are the in-
put voltage rating and the RMS current rating. With a nominal
input voltage of 28V, an aluminum electrolytic aluminum elec-
trolytic capacitor with a voltage rating greater than 42V (1.5 x
V
IN) would be needed. Since the the next higher capacitor
voltage rating is 50V, a 50V capacitor should be used. The
capacitor voltage rating of (1.5 x V
IN) is a conservative guide-
line, and can be modified somewhat if desired.
The RMS current rating requirement for the input capacitor of
a buck regulator is approximately 12 the DC load current. In
this example, with a 400 mA load, a capacitor with a RMS
current rating of at least 200 mA is needed.
The curves shown in
Figure 13 can be used to select an ap-
propriate input capacitor. From the curves, locate the 50V
line and note which capacitor values have RMS current rat-
ings greater than 200 mA. A 47 F/50V low ESR electrolytic
capacitor capacitor is needed.
For a through hole design, a 47 F/50V electrolytic capacitor
(Panasonic HFQ series or Nichicon PL series or equivalent)
would be adequate. Other types or other manufacturers ca-
pacitors can be used provided the RMS ripple current ratings
are adequate.
For surface mount designs, solid tantalum capacitors are
recommended. The TPS series available from AVX, and the
593D series from Sprague are both surge current tested.
To further simplify the buck regulator design procedure, Na-
tional Semiconductor is making available computer design
software to be used with the Simple Switcher line ot switch-
ing regulators. Switchers Made Simple (version 4.1 or later)
is available from National’s web site, www.national.com.
Output
Volt-
age
(V)
Through Hole Output Capacitor
Surface Mount Output Capacitor
Panasonic
Nichicon PL
Feedforward
AVX TPS
Sprague
Feedforward
HFQ Series
Series
Capacitor
Series
595D Series
Capacitor
(F/V)
1.2
220/25
0
220/10
0
4
180/25
4.7 nF
100/10
120/10
4.7 nF
6
82/25
4.7 nF
100/10
120/10
4.7 nF
9
82/25
3.3 nF
100/16
3.3 nF
12
82/25
2.2 nF
100/16
2.2 nF
15
82/25
1.5 nF
68/20
100/20
1.5 nF
24
82/50
120/50
1 nF
10/35
15/35
220 pF
28
82/50
120/50
820 pF
10/35
15/35
220 pF
FIGURE 3. Output Capacitor and Feedforward Capacitor Selection Table
LM2594/LM2594HV
www.national.com
14
相關PDF資料
PDF描述
LM2594HV-12MWC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594HV-12MDC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594-3.3MDC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2595J-12-QML 2.6 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, CDIP16
5962-9687901QEA 2.6 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, CDIP16
相關代理商/技術參數
參數描述
LM2594APDBCKGEVB 功能描述:電源管理IC開發工具 LM2594ADJ PDIP8 BUCK DB RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2594ASCBCKGEVB 功能描述:BOARD EVAL FOR LM2594ADJ 8-SOIC RoHS:是 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC,步升 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
LM2594DADJG 功能描述:直流/直流開關調節器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
LM2594DADJR2G 功能描述:直流/直流開關調節器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
LM2594HVM-12 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT