參數資料
型號： LM2594-5.0MWC
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
封裝： WAFER
文件頁數： 33/33頁
文件大?。?/td> 837K
代理商： LM2594-5.0MWC
LM2594/LM2594HV Series Buck Regulator Design Procedure (Fixed
Output)
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
Given:
V
OUT = Regulated Output Voltage (3.3V, 5V or 12V)
V
IN(max) = Maximum DC Input Voltage
I
LOAD(max) = Maximum Load Current
Given:
V
OUT =5V
V
IN(max) = 12V
I
LOAD(max) = 0.4A
1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from
Fig-
ures 4, 5 or Figure 6. (Output voltages of 3.3V, 5V, or 12V re-
spectively.) For all other voltages, see the design procedure
for the adjustable version.
B. From the inductor value selection guide, identify the induc-
tance region intersected by the Maximum Input Voltage line
and the Maximum Load Current line. Each region is identified
by an inductance value and an inductor code (LXX).
C. Select an appropriate inductor from the four manufactur-
er’s part numbers listed in
Figure 8.
1. Inductor Selection (L1)
A. Use the inductor selection guide for the 5V version shown
in
Figure 5.
B. From the inductor value selection guide shown in
Figure 5,
the inductance region intersected by the 12V horizontal line
and the 0.4A vertical line is 100 H, and the inductor code is
L20.
C. The inductance value required is 100 H. From the table
in
Figure 8, go to the L20 line and choose an inductor part
number from any of the four manufacturers shown. (In most
instance, both through hole and surface mount inductors are
available.)
2. Output Capacitor Selection (C
OUT)
A. In the majority of applications, low ESR (Equivalent Series
Resistance) electrolytic capacitors between 82 F and
220 F and low ESR solid tantalum capacitors between 15
F and 100 F provide the best results. This capacitor should
be located close to the IC using short capacitor leads and
short copper traces. Do not use capacitors larger than
220 F.
For additional information, see section on output capaci-
tors in application information section.
B. To simplify the capacitor selection procedure, refer to the
quick design component selection table shown in
Figure 2.
This table contains different input voltages, output voltages,
and load currents, and lists various inductors and output ca-
pacitors that will provide the best design solutions.
C. The capacitor voltage rating for electrolytic capacitors
should be at least 1.5 times greater than the output voltage,
and often much higher voltage ratings are needed to satisfy
the low ESR requirements for low output ripple voltage.
D. For computer aided design software, see
Switchers Made
Simple version 4.1 or later.
2. Output Capacitor Selection (C
OUT)
A. See section on output capacitors in application infor-
mation section.
B. From the quick design component selection table shown
in
Figure 2, locate the 5V output voltage section. In the load
current column, choose the load current line that is closest to
the current needed in your application, for this example, use
the 0.5A line. In the maximum input voltage column, select
the line that covers the input voltage needed in your applica-
tion, in this example, use the 15V line. Continuing on this line
are recommended inductors and capacitors that will provide
the best overall performance.
The capacitor list contains both through hole electrolytic and
surface mount tantalum capacitors from four different capaci-
tor manufacturers. It is recommended that both the manufac-
turers and the manufacturer’s series that are listed in the
table be used.
In this example aluminum electrolytic capacitors from several
different manufacturers are available with the range of ESR
numbers needed.
120 F
25V
Panasonic HFQ Series
120 F
25V
Nichicon PL Series
C. For a 5V output, a capacitor voltage rating at least 7.5V or
more is needed. But, in this example, even a low ESR,
switching grade, 120 F 10V aluminum electrolytic capacitor
would exhibit approximately 400 m
of ESR (see the curve
in
Figure 14 for the ESR vs voltage rating). This amount of
ESR would result in relatively high output ripple voltage. To
reduce the ripple to 1% of the output voltage, or less, a ca-
pacitor with a higher voltage rating (lower ESR) should be se-
lected. A 16V or 25V capacitor will reduce the ripple voltage
by approximately half.
LM2594/LM2594HV
www.national.com
9
相關PDF資料
PDF描述
LM2594-ADJMDC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594-ADJMWC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594HV-12MWC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594HV-12MDC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2594-3.3MDC 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
相關代理商/技術參數
參數描述
LM2594APDBCKGEVB 功能描述:電源管理IC開發工具 LM2594ADJ PDIP8 BUCK DB RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2594ASCBCKGEVB 功能描述:BOARD EVAL FOR LM2594ADJ 8-SOIC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
LM2594DADJG 功能描述:直流/直流開關調節器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
LM2594DADJR2G 功能描述:直流/直流開關調節器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
LM2594HVM-12 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*