- 您現在的位置：買賣IC網 > PDF目錄358822 > LM2588T-ADJ (NATIONAL SEMICONDUCTOR CORP) SIMPLE SWITCHER 5A Flyback Regulator with PDF資料下載
參數資料
| 型號： | LM2588T-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SIMPLE SWITCHER 5A Flyback Regulator with |
| 中文描述： | 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PSFM7 |
| 封裝： | BENT STAGGERED, TO-220, 7 PIN |
| 文件頁數： | 26/29頁 |
| 文件大?。?/td> | 786K |
| 代理商： | LM2588T-ADJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁
Application Hints
(Continued)
CIRCUIT LAYOUT GUIDELINES
As in any switching regulator, layout is very important. Rap-
idly switching currents associated with wiring inductance
generate voltage transients which can cause problems. For
minimal inductance and ground loops, keep the length of the
leads and traces as short as possible. Use single point
grounding or ground plane construction for best results.
Separate the signal grounds from the power grounds (as in-
dicated in Figure 48). When using the Adjustable version,
physically locate the programming resistors as near the
regulator IC as possible, to keep the sensitive feedback wir-
ing short.
HEAT SINK/THERMAL CONSIDERATIONS
In many cases, a heat sink is not required to keep the
LM2588 junction temperature within the allowed operating
temperature range. For each application, to determine
whether or not a heat sink will be required, the following must
be identified:
1) Maximum ambient temperature (in the application).
2) Maximum regulator power dissipation (in the application).
3) Maximum allowed junction temperature (125C for the
LM2588). For a safe, conservative design, a temperature ap-
proximately 15C cooler than the maximum junction tem-
perature should be selected (110C).
4) LM2588 package thermal resistances
θ
JA
and
θ
JC
(given
in the Electrical Characteristics).
Total power dissipated (P
D
) by the LM2588 can be estimated
as follows:
Boost:
V
is the minimum input voltage, V
is the output voltage,
N is the transformer turns ratio, D is the duty cycle, and I
LOAD
is the maximum load current (and
∑
I
is the sum of the
maximum load currents for multiple-output flyback regula-
tors). The duty cycle is given by:
Boost:
where V
is the forward biased voltage of the diode and is
typically 0.5V for Schottky diodes and 0.8V for fast recovery
diodes. V
is the switch saturation voltage and can be
found in the Characteristic Curves.
When no heat sink is used, the junction temperature rise is:
T
J
= P
D
θ
JA
.
Adding the junction temperature rise to the maximum ambi-
ent temperature gives the actual operating junction tempera-
ture:
T
J
=
T
J
+ T
A
.
If the operating junction temperature exceeds the maximum
junction temperatue in item 3 above, then a heat sink is re-
quired. When using a heat sink, the junction temperature rise
can be determined by the following:
T
J
= P
D
(
θ
JC
+
θ
Interface
+
θ
Heat Sink
)
Again, the operating junction temperature will be:
T
J
=
T
J
+ T
A
As before, if the maximum junction temperature is exceeded,
a larger heat sink is required (one that has a lower thermal
resistance).
Included in the Switchers Made Simple design software is a
more precise (non-linear) thermal model that can be used to
determine junction temperature with different input-output
parameters or different component values. It can also calcu-
late the heat sink thermal resistance required to maintain the
regulator junction temperature below the maximum operat-
ing temperature.
DS012420-59
FIGURE 48. Circuit Board Layout
www.national.com
26
相關PDF資料 |
PDF描述 |
|---|---|
| LM2588T-5.0 | SIMPLE SWITCHER 5A Flyback Regulator with |
| LM2588T-3.3 | SIMPLE SWITCHER 5A Flyback Regulator with |
| LM2588T-12 | SIMPLE SWITCHER 5A Flyback Regulator with |
| LM2588S-5.0 | SIMPLE SWITCHER 5A Flyback Regulator with |
| LM2588SX-ADJ | SIMPLE SWITCHER 5A Flyback Regulator with |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2588T-ADJ | 制造商:Texas Instruments 功能描述:SWITCHING REG 5A ADJ 2588 TO2207 |
| LM2588T-ADJ/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM258AD | 功能描述:運算放大器 - 運放 Dual Operational Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM258ADE4 | 功能描述:運算放大器 - 運放 Dual Operational Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM258ADG4 | 功能描述:運算放大器 - 運放 Dual Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。