- 您現在的位置：買賣IC網 > PDF目錄30746 > LM2576HV-5MDC (NATIONAL SEMICONDUCTOR CORP) 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC PDF資料下載
參數資料
| 型號： | LM2576HV-5MDC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| 封裝： | DIE |
| 文件頁數： | 5/27頁 |
| 文件大?。?/td> | 741K |
| 代理商： | LM2576HV-5MDC |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
LM2576 Series Buck Regulator Design Procedure (Continued)
PROCEDURE (Adjustable Output Voltage Versions)
EXAMPLE (Adjustable Output Voltage Versions)
2. Inductor Selection (L1)
A. Calculate the inductor Volt
microsecond constant,
E
T(V
s),
from
the
following
formula:
B. Use the E
T value from the previous formula and
match it with the E
T number on the vertical axis of the
Inductor Value Selection Guide shown in
Figure 7.
C. On the horizontal axis, select the maximum load cur-
rent.
D. Identify the inductance region intersected by the E
T
value and the maximum load current value, and note the
inductor code for that region.
E. Identify the inductor value from the inductor code, and
select an appropriate inductor from the table shown in
Figure 9. Part numbers are listed for three inductor manu-
facturers. The inductor chosen must be rated for opera-
tion at the LM2576 switching frequency (52 kHz) and for a
current rating of 1.15 x I
LOAD. For additional inductor in-
formation, see the inductor section in the application hints
section of this data sheet.
2. Inductor Selection (L1)
A. Calculate E
T(V s)
B. E
T = 115 V s
C. I
LOAD(Max) = 3A
D. Inductance Region = H150
E. Inductor Value = 150 H
Choose from AIE part
#415-0936 Pulse Engineering part #PE-531115, or
Renco part #RL2445.
3. Output Capacitor Selection (C
OUT)
A. The value of the output capacitor together with the in-
ductor defines the dominate pole-pair of the switching
regulator loop. For stable operation, the capacitor must
satisfy the following requirement:
The above formula yields capacitor values between 10 F
and 2200 F that will satisfy the loop requirements for
stable operation. But to achieve an acceptable output
ripple voltage, (approximately 1% of the output voltage)
and transient response, the output capacitor may need to
be several times larger than the above formula yields.
B. The capacitor’s voltage rating should be at last 1.5
times greater than the output voltage. For a 10V regulator,
a rating of at least 15V or more is recommended. Higher
voltage electrolytic capacitors generally have lower ESR
numbers, and for this reason it may be necessary to se-
lect a capacitor rate for a higher voltage than would nor-
mally be needed.
3. Output Capacitor Selection (C
OUT)
However, for acceptable output ripple voltage select
C
OUT ≥ 680 F
C
OUT = 680 F electrolytic capacitor
4. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.2
times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output
short, the diode should have a current rating equal to the
maximum current limit of the LM2576. The most stressful
condition for this diode is an overload or shorted output.
See diode selection guide in
Figure 8.
B. The reverse voltage rating of the diode should be at
least 1.25 times the maximum input voltage.
4. Catch Diode Selection (D1)
A. For this example, a 3.3A current rating is adequate.
B. Use a 30V 31DQ03 Schottky diode, or any of the sug-
gested fast-recovery diodes in
Figure 8.
5. Input Capacitor (C
IN)
An aluminum or tantalum electrolytic bypass capacitor lo-
cated close to the regulator is needed for stable opera-
tion.
5. Input Capacitor (C
IN)
A 100 F aluminum electrolytic capacitor located near the
input and ground pins provides sufficient bypassing.
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM2576-15MDC | 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2576-12MWC | 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2577SX-15/NOPB | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, PSSO5 |
| LM2578N | 0.75 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM2591HVADJMWC | 3 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2576HV-ADJ | 制造商:FCI 制造商全稱:First Components International 功能描述:SMIPLE SWITCHER 3.0A Step-Down Voltage Regulator |
| LM2576HVS-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2576HVS-12/NOPB | 功能描述:直流/直流開關轉換器 3A STEP-DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2576HVS-15 | 功能描述:IC REG BUCK 15V 3A TO263-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SIMPLE SWITCHER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2576HVS-3.3 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。