- 您現在的位置：買賣IC網 > PDF目錄376111 > LM2576-5 (Motorola, Inc.) Easy Switcher 3.0A Step-Down Voltage Regulator PDF資料下載
參數資料
| 型號： | LM2576-5 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Easy Switcher 3.0A Step-Down Voltage Regulator |
| 中文描述： | 輕松切換3.0A的降壓穩壓器 |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 301K |
| 代理商： | LM2576-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LM2576
11
MOTOROLA ANALOG IC DEVICE DATA
Procedure (Fixed Output Voltage Version) (continued)
In order to simplify the switching regulator design, a step–by–step
design procedure and some examples are provided.
Procedure
Example
5. Output Capacitor Selection (Cout)
A.
Since the LM2576 is a forward–mode switching regulator
with voltage mode control, its open loop 2–pole–1–zero
frequency characteristic has the dominant pole–pair
determined by the output capacitor and inductor values. For
stable operation and an acceptable ripple voltage,
(approximately 1% of the output voltage) a value between
680
μ
F and 2000
μ
F is recommended.
B.
Due to the fact that the higher voltage electrolytic capacitors
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating at least 8.0 V is appropriate, and a 10 V or
16 V rating is recommended.
5. Output Capacitor Selection (Cout)
A.
Cout = 680
μ
F to 2000
μ
F standard aluminium electrolytic.
B.
Capacitor voltage rating = 20 V.
Procedure (Adjustable Output Version: LM2576–ADJ)
Procedure
Example
Given Parameters:
Vout = Regulated Output Voltage
Vin(max) = Maximum DC Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 8.0 V
Vin(max) = 25 V
ILoad(max) = 2.5 A
1. Programming Output Voltage
To select the right programming resistor R1 and R2 value (see
Figure 2) use the following formula:
Resistor R1 can be between 1.0 k and 5.0 k
. (For best
temperature coefficient and stability with time, use 1% metal
film resistors).
Vout
Vref
Vout
Vref
1.0
R2
R1
R2
R1
– 1.0
where Vref = 1.23 V
1. Programming Output Voltage
(selecting R1 and R2)
Select R1 and R2:
R2 = 9.91 k
, choose a 9.88 k metal film resistor.
R2
R1
Vout
Vref
1.0
1.8 k
8.0 V
1.23 V
1.0
Vout
1.23 1.0
R2
R1
Select R1 = 1.8 k
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin Gnd This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value
.
For additional information see input capacitor section in the
“Application Hints” section of this data sheet.
2. Input Capacitor Selection (Cin)
A 100
μ
F, 150 V aluminium electrolytic capacitor located near
the input and ground pin provides sufficient bypassing.
3. Catch Diode Selection (D1)
A.
Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2576 to be able to withstand a continuous output short.
B.
The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A.
For this example, a 3.0 A current rating is adequate.
B.
Use a 30 V 1N5821 Schottky diode or any
suggested fast recovery diode in the
Table 1.
相關PDF資料 |
PDF描述 |
|---|---|
| LM2576-ADJ | Easy Switcher 3.0A Step-Down Voltage Regulator |
| LM2904V | LinCMOS<TM> Precision Dual Operational Amplifier 8-PDIP -40 to 85 |
| LM29021 | Amplifiers and Comparators |
| LM2902V | LinCMOS(TM) Programmable Low-Power Operational Amplifier 8-PDIP -40 to 85 |
| LM2935D2T | Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs 20-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2576-5.0 | 制造商:FCI 制造商全稱:First Components International 功能描述:SMIPLE SWITCHER 3.0A Step-Down Voltage Regulator |
| LM2576-5.0BT | 功能描述:IC REG BUCK 5V 3A TO220-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2576-5.0BT⒂ | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:52kHz Simple 3A Buck Voltage Regulator |
| LM2576-5.0BU | 功能描述:IC REG BUCK 5V 3A TO263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2576-5.0BU TR | 功能描述:IC REG BUCK 5V 3A TO263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
發布緊急采購，3分鐘左右您將得到回復。