參數資料
型號： LM2574HVADJMWC
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC
封裝： WAFER
文件頁數： 7/33頁
文件大?。?/td> 814K
代理商： LM2574HVADJMWC
LM2574 Series Buck Regulator Design Procedure (Continued)
PROCEDURE (Adjustable Output Voltage Versions)
EXAMPLE (Adjustable Output Voltage Versions)
3. Output Capacitor Selection (C
OUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation, the capacitor must satisfy the following
requirement:
The above formula yields capacitor values between 5 F and
1000 F that will satisfy the loop requirements for stable op-
eration. But to achieve an acceptable output ripple voltage,
(approximately 1% of the output voltage) and transient re-
sponse, the output capacitor may need to be several times
larger than the above formula yields.
B. The capacitor’s voltage rating should be at last 1.5 times
greater than the output voltage. For a 24V regulator, a rating
of at least 35V is recommended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reasion it may be necessary to se-
lect a capacitor rate for a higher voltage than would normally
be needed.
3. Output Capacitor Selection (C
OUT)
However, for acceptable output ripple voltage select
C
OUT ≥ 100 F
C
OUT = 100 F electrolytic capacitor
4. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.5 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum cur-
rent limit of the LM2574. The most stressful condition for this
diode is an overload or shorted output condition. Suitable di-
odes are shown in the selection guide of
Figure 9.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
4. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 50V MBR150 or 11DQ05 Schottky diode, or any of
the suggested fast-recovery diodes in
Figure 9.
5. Input Capacitor (C
IN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
5. Input Capacitor (C
IN)
A 22 F aluminum electrolytic capacitor located near the input
and ground pins provides sufficient bypassing. See (
Figure 9).
To further simplify the buck regulator design procedure, Na-
tional Semiconductor is making available computer design
software to be used with the Simple Switcher line of switching
regulators. Switchers Made Simple (version 3.3) is available
ona(312") diskette for IBM compatible computers from a Na-
tional Semiconductor sales office in your area.
www.national.com
15
相關PDF資料
PDF描述
LM2574HVN-3.3/NOPB 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8
LM2574-5.0MWC 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC
LM2574-ADJMWC 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC
LM2574N-15/NOPB 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8
LM2574M-15/NOPB 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO14
相關代理商/技術參數
參數描述
LM2574HVM-12 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
LM2574HVM-12/NOPB 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
LM2574HVM-12/NOPB 制造商:Texas Instruments 功能描述:DC/DC Converter IC
LM2574HVM-15 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
LM2574HVM-15/NOPB 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*