- 您現在的位置：買賣IC網 > PDF目錄44546 > LM2574-ADJMWC (NATIONAL SEMICONDUCTOR CORP) 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC PDF資料下載
參數資料
| 型號： | LM2574-ADJMWC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| 封裝： | WAFER |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 814K |
| 代理商： | LM2574-ADJMWC |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
LM2574 Series Buck Regulator Design Procedure
PROCEDURE (Fixed Output Voltage Versions)
EXAMPLE (Fixed Output Voltage Versions)
Given:
V
OUT = Regulated Output Voltage (3.3V, 5V, 12V, or 15V)
V
IN(Max) = Maximum Input Voltage
I
LOAD(Max) = Maximum Load Current
Given:
V
OUT = 5V
V
IN(Max) = 15V
I
LOAD(Max) = 0.4A
1. Inductor Selection (L1)
A. Select the correct Inductor value selection guide from
Fig-
ures 4, 5, 6,or Figure 7. (Output voltages of 3.3V, 5V, 12V or
15V respectively). For other output voltages, see the design
procedure for the adjustable version.
B. From the inductor value selection guide, identify the induc-
tance region intersected by V
IN(Max) and ILOAD(Max).
C. Select an appropriate inductor from the table shown in
Fig-
ure 3. Part numbers are listed for three inductor manufactur-
ers. The inductor chosen must be rated for operation at the
LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 x I
LOAD. For additional inductor information, see the in-
ductor section in the Application Hints section of this data
sheet.
1. Inductor Selection (L1)
A. Use the selection guide shown in
Figure 5.
B. From the selection guide, the inductance area intersected
by the 15V line and 0.4A line is 330.
C. Inductor value required is 330 H. From the table in
Figure
3, choose Pulse Engineering PE-52627, Renco RL-1284-330,
or NPI NP5920/5921.
2. Output Capacitor Selection (C
OUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation and an acceptable output ripple voltage,
(approximately 1% of the output voltage) a value between
100 F and 470 F is recommended.
B. The capacitor’s voltage rating should be at least 1.5 times
greater than the output voltage. For a 5V regulator, a rating of
at least 8V is appropriate, and a 10V or 15V rating is recom-
mended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reason it may be necessary to se-
lect a capacitor rated for a higher voltage than would normally
be needed.
2. Output Capacitor Selection (C
OUT)
A. C
OUT = 100 F to 470 F standard aluminum electrolytic.
B. Capacitor voltage rating = 20V.
3. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.5 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum cur-
rent limit of the LM2574. The most stressful condition for this
diode is an overload or shorted output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 20V 1N5817 or SR102 Schottky diode, or any of the
suggested fast-recovery diodes shown in
Figure 9.
4. Input Capacitor (C
IN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
4. Input Capacitor (C
IN)
A 22 F aluminum electrolytic capacitor located near the input
and ground pins provides sufficient bypassing.
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM2574N-15/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM2574M-15/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO14 |
| LM2574-ADJMDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-12MDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-5.0MDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2574BN | 功能描述:IC REG BUCK ADJ 0.5A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2574BWM | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| LM2574DW | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator |
| LM2574DW-ADJ | 功能描述:直流/直流開關調節器 500mA Adj. Step Down RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2574DW-ADJR2 | 功能描述:直流/直流開關調節器 500mA Adj. Step Down RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。