- 您現在的位置：買賣IC網 > PDF目錄44546 > LM25576Q0MH (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO20 PDF資料下載
參數資料
| 型號： | LM25576Q0MH |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO20 |
| 封裝： | TSSOP-20 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 408K |
| 代理商： | LM25576Q0MH |
Application Information
EXTERNAL COMPONENTS
The procedure for calculating the external components is il-
lustrated with the following design example. The circuit shown
in Figure 1 is configured for the following specifications:
V
OUT = 5V
V
IN = 7V to 42V
Fs = 300kHz
Minimum load current (for CCM) = 250mA
Maximum load current = 3A
R3 (R
T)
R
T sets the oscillator switching frequency. Generally, higher
frequency applications are smaller but have higher losses.
Operation at 300kHz was selected for this example as a rea-
sonable compromise for both small size and high efficiency.
The value of R
T for 300kHz switching frequency can be cal-
culated as follows:
The nearest standard value of 21k
was chosen for R
T.
L1
The inductor value is determined based on the operating fre-
quency, load current, ripple current, and the minimum and
maximum input voltage (V
IN(min), VIN(max)).
30071210
FIGURE 8. Inductor Current Waveform
To keep the circuit in continuous conduction mode (CCM), the
maximum ripple current I
RIPPLE should be less than twice the
minimum load current, or 0.5Ap-p. Using this value of ripple
current, the value of inductor (L1) is calculated using the fol-
lowing:
This procedure provides a guide to select the value of L1. The
nearest standard value (33H) will be used. L1 must be rated
for the peak current (I
PK+) to prevent saturation. During normal
loading conditions, the peak current occurs at maximum load
current plus maximum ripple. During an overload condition
the peak current is limited to 4.2A nominal (5.1A maximum).
The selected inductor (see Table 1) has a conservative 6.2
Amp saturation current rating. For this manufacturer, the sat-
uration rating is defined as the current necessary for the
inductance to reduce by 30%, at 20°C.
C3 (C
RAMP)
With the inductor value selected, the value of C3 (C
RAMP)
necessary for the emulation ramp circuit is:
C
RAMP = L x 10
-5
Where L is in Henrys
With L1 selected for 33H the recommended value for C3 is
330pF.
C9, C10
The output capacitors, C9 and C10, smooth the inductor rip-
ple current and provide a source of charge for transient load-
ing conditions. For this design a 22F ceramic capacitor and
a 150F SP organic capacitor were selected. The ceramic
capacitor provides ultra low ESR to reduce the output ripple
voltage and noise spikes, while the SP capacitor provides a
large bulk capacitance in a small volume for transient loading
conditions. An approximation for the output ripple voltage is:
D1
A Schottky type re-circulating diode is required for all
LM25576Q0 applications. Ultra-fast diodes are not recom-
mended and may result in damage to the IC due to reverse
recovery current transients. The near ideal reverse recovery
characteristics and low forward voltage drop are particularly
important diode characteristics for high input voltage and low
output voltage applications common to the LM25576Q0. The
reverse recovery characteristic determines how long the cur-
rent surge lasts each cycle when the buck switch is turned on.
The reverse recovery characteristics of Schottky diodes min-
imize the peak instantaneous power in the buck switch oc-
curring during turn-on each cycle. The resulting switching
losses of the buck switch are significantly reduced when using
a Schottky diode. The reverse breakdown rating should be
selected for the maximum V
IN, plus some safety margin.
The forward voltage drop has a significant impact on the con-
version efficiency, especially for applications with a low output
voltage. “Rated” current for diodes vary widely from various
manufacturers. The worst case is to assume a short circuit
load condition. In this case the diode will carry the output cur-
rent almost continuously. For the LM25576Q0 this current can
be as high as 4.2A. Assuming a worst case 1V drop across
the diode, the maximum diode power dissipation can be as
high as 4.2W. For the reference design a 60V Schottky in a
DPAK package was selected.
C1, C2
The regulator supply voltage has a large source impedance
at the switching frequency. Good quality input capacitors are
necessary to limit the ripple voltage at the VIN pin while sup-
plying most of the switch current during the on-time. When the
buck switch turns on, the current into the VIN pin steps to the
lower peak of the inductor current waveform, ramps up to the
peak value, then drops to zero at turn-off. The average current
into VIN during the on-time is the load current. The input ca-
pacitance should be selected for RMS current rating and
www.national.com
14
LM25576Q0
相關PDF資料 |
PDF描述 |
|---|---|
| LM2574HVADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574HVN-3.3/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM2574-5.0MWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-ADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574N-15/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25576Q0MH/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25576Q0MHX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25576QMH/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25576QMHX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2567 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LAN DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。