- 您現在的位置：買賣IC網 > PDF目錄44546 > LM25574Q0MTX (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO16 PDF資料下載
參數資料
| 型號： | LM25574Q0MTX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO16 |
| 封裝： | TSSOP-16 |
| 文件頁數： | 2/20頁 |
| 文件大小： | 394K |
| 代理商： | LM25574Q0MTX |
30071007
FIGURE 5. Simplified Oscillator Block Diagram and SYNC I/O Circuit
Error Amplifier and PWM
Comparator
The internal high gain error amplifier generates an error signal
proportional to the difference between the regulated output
voltage and an internal precision reference (1.225V). The
output of the error amplifier is connected to the COMP pin
allowing the user to provide loop compensation components,
generally a type II network, as illustrated in Figure 1. This
network creates a pole at DC, a zero and a noise reducing
high frequency pole. The PWM comparator compares the
emulated current sense signal from the RAMP generator to
the error amplifier output voltage at the COMP pin.
RAMP Generator
The ramp signal used in the pulse width modulator for current
mode control is typically derived directly from the buck switch
current. This switch current corresponds to the positive slope
portion of the output inductor current. Using this signal for the
PWM ramp simplifies the control loop transfer function to a
single pole response and provides inherent input voltage
feed-forward compensation. The disadvantage of using the
buck switch current signal for PWM control is the large leading
edge spike due to circuit parasitics that must be filtered or
blanked. Also, the current measurement may introduce sig-
nificant propagation delays. The filtering, blanking time and
propagation delay limit the minimum achievable pulsewidth.
In applications where the input voltage may be relatively large
in comparison to the output voltage, controlling small
pulsewidths and duty cycles is necessary for regulation. The
LM25574Q0 utilizes a unique ramp generator, which does not
actually measure the buck switch current but rather recon-
structs the signal. Reconstructing or emulating the inductor
current provides a ramp signal to the PWM comparator that
is free of leading edge spikes and measurement or filtering
delays. The current reconstruction is comprised of two ele-
ments; a sample & hold DC level and an emulated current
ramp.
www.national.com
10
LM25574Q0
相關PDF資料 |
PDF描述 |
|---|---|
| LM25576Q0MH | SWITCHING REGULATOR, PDSO20 |
| LM2574HVADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574HVN-3.3/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM2574-5.0MWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-ADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25574Q0MTX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25574-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25574/LM25574-Q1 SIMPLE SWITCHER 42V, 0.5A Step-Down Switching Regulator |
| LM25574QMT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25574/LM25574-Q1 SIMPLE SWITCHER 42V, 0.5A Step-Down Switching Regulator |
| LM25574QMT/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25574QMTX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25574/LM25574-Q1 SIMPLE SWITCHER 42V, 0.5A Step-Down Switching Regulator |
發布緊急采購，3分鐘左右您將得到回復。