- 您現在的位置：買賣IC網 > PDF目錄385476 > LM1972MX (NATIONAL SEMICONDUCTOR CORP) Tone/Volume/Balance Control PDF資料下載
參數資料
| 型號： | LM1972MX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | Tone/Volume/Balance Control |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | SOP-20 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 301K |
| 代理商： | LM1972MX |
Application Information
(Continued)
INPUT IMPEDANCE
The input impedance of a μPot is constant at a nominal
40 k
. To eliminate any unwanted DC components from
propagating through the device it is common to use 1 μF in-
put coupling caps. This is not necessary, however, if the dc
offset from the previous stage is negligible. For higher per-
formance systems, input coupling caps are preferred.
OUTPUT IMPEDANCE
The output of a μPot varies typically between 25 k
and
35 k
and changes nonlinearly with step changes. Since a
μPot is made up of a resistor ladder network with a logarith-
mic attenuation, the output impedance is nonlinear. Due to
this configuration, a μPot cannot be considered as a linear
potentiometer, but can be considered only as a logarithmic
attenuator.
It should be noted that the linearity of a μPot cannot be mea-
sured directly without a buffer because the input impedance
of most measurement systems is not high enough to provide
the required accuracy. Due to the low impedance of the mea-
surement system, the output of the μPot would be loaded
down and an incorrect reading will result. To prevent loading
from occurring, a JFET input op amp should be used as the
buffer/amplifier. The performance of a μPot is limited only by
the performance of the external buffer/amplifier.
MUTE FUNCTION
One major feature of a μPot is its ability to mute the input sig-
nal to an attenuation level of 104dB as shown in Figure 3
This is accomplished internally by physically isolating the
output from the input while also grounding the output pin
through approximately 2 k
.
The mute function is obtained during power-up of the device
or by sending any binary data of 01111111 and above (to
11111111) serially to the device. The device may be placed
into mute from a previous attenuation setting by sending any
of the above data. This allows the designer to place a mute
button onto his system which could cause a microcontroller
to send the appropriate data to a μPot and thus mute any or
all channels. Since this function is achieved through soft-
ware, the designer has a great amount of flexibility in config-
uring the system.
DC INPUTS
Although the μPot was designed to be used as an attenuator
for signals within the audio spectrum, the device is capable
of tracking an input DC voltage. The device will track DC
voltages to a diode drop above each supply rail.
One point to remember about DC tracking is that with a
buffer at the output of the μPot, the resolution of DC tracking
will depend upon the gain configuration of that output buffer
and its supply voltage. It should also be remembered that the
output buffer’s supply voltage does not have to be the same
as the μPot’s supply voltage. This could allow for more reso-
lution when DC tracking.
SERIAL DATA FORMAT
The LM1972 uses a 3-wire serial communication format that
is easily controlled by a microcontroller. The timing for the
3-wire set, comprised of DATA-IN, CLOCK, and LOAD/
SHIFT is shown in Figure 2 Figure 9 exhibits in block dia-
gram form how the digital interface controls the tap switches
which select the appropriate attenuation level.As depicted in
Figure 2 the LOAD/SHIFT line is to go low at least 150 ns
before the rising edge of the first clock pulse and is to remain
low throughout the transmission of each set of 16 data bits.
The serial data is comprised of 8 bits for channel selection
and 8 bits for attenuation setting. For both address data and
attenuation setting data, the MSB is sent first and the 8 bits
of address data are to be sent before the 8 bits of attenuation
data. Please refer to Figure 7 to confirm the serial data for-
mat transfer process.
TABLE 1. LM1972 Micropot Attenuator
Register Set Description
MSB:
LSB
Address Register (Byte 0)
0000 0000
0000 0001
0000 0010
Data Register (Byte 1)
Contents
0000 0000
0000 0001
0000 0010
0000 0011
: : : : :
0001 1110
0001 1111
0010 0000
0010 0001
0010 0010
: : : : :
0101 1110
0101 1111
0110 0000
0110 0001
0110 0010
: : : : :
0111 1100
0111 1101
0111 1110
0111 1111
1000 0000
: : : : :
Channel 1
Channel 2
Channel 3
Attenuation Level dB
0.0
0.5
1.0
1.5
: :
15.0
15.5
16.0
16.5
17.0
: :
47.0
47.5
48.0
49.0
50.0
: :
76.0
77.0
78.0
100.0 (Mute)
100.0 (Mute)
: :
DS011978-9
FIGURE 6. Mono Panning Circuit
www.national.com
6
相關PDF資料 |
PDF描述 |
|---|---|
| LM1972M | Pot 2-Channel 78dB Audio Attenuator with Mute |
| LM1972N | Pot 2-Channel 78dB Audio Attenuator with Mute |
| LM19CIZ | 2.4V, 10uA, TO-92 Temperature Sensor |
| LM218H | Operational Amplifiers |
| LM318H | Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1972MX/NOPB | 功能描述:有源衰減器 RoHS:否 制造商:TriQuint Semiconductor 通道數量: 最大頻率: 阻抗: 最大 VSWR: 位數: 最大工作溫度: 最小工作溫度: |
| LM1972N | 功能描述:IC AUDIO ATTENUATOR 2CH 20-DIP RoHS:否 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:- 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| LM1972N | 制造商:Texas Instruments 功能描述:AUDIO ATTENUATOR 78DB 1972 DIP20 |
| LM1972N/NOPB | 制造商:Texas Instruments 功能描述:Digital Attenuator 104dB Attenuation 20-Pin PDIP Rail |
| LM1973 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:レPot⑩3-Channel 76dB Audio Attenuator with Mute |
發布緊急采購，3分鐘左右您將得到回復。